Home › Drivetrain › CLUTCH › CLUTCH UNIT(for 1VD-FTV)
RM2660E _52 Drivetrain _052808 CLUTCH _0255318 CLUTCH UNIT(for 1VD-FTV) A

CLUTCH  CLUTCH UNIT(for 1VD-FTV)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

C358759E01
2.552,1.385 2.75,0.906 2.75,0.906 2.875,0.906 false 0.844,3.073 2.833,3.271 1.99,0.198 10 false Flywheel Side 2.927,0.823 3.344,1 0.417,0.177 10 false SST

a.

Insert SST into the clutch disc, then insert the clutch disc into the flywheel.

SST
09301-00120  

NOTICE:

Take care not to insert the clutch disc in the wrong direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

C173324E02
1.198,0.719 0.896,0.365 0.896,0.365 1.125,0.719 true 2.333,1.281 2.563,0.74 false 2.563,0.74 2.74,0.74 false 0.917,0.052 1.229,0.24 0.313,0.188 10 false 1, 5 1.76,1.958 2.094,2.115 0.333,0.156 10 false 2, 6 1.865,0.031 2.042,0.208 0.177,0.177 10 false 3 2.208,0.51 2.427,0.688 0.219,0.177 10 false 10 2.219,0.99 2.375,1.167 0.156,0.177 10 false 8 1.406,1.979 1.563,2.135 0.156,0.156 10 false 4 0.667,1.677 0.823,1.833 0.156,0.156 10 false 9 0.552,0.896 0.708,1.052 0.156,0.156 10 false 7 0.156,0.25 0.969,0.427 0.813,0.177 10 false Matchmark 2.781,0.656 3.083,0.833 0.302,0.177 10 false SST

a.

Align the matchmark on the clutch cover with the one on the flywheel.


b.

In the order shown in the illustration, temporarily install the 8 bolts starting from the bolt located near the knock pin on the top.


c.

Check that the disc is in the center by lightly moving SST up and down, and left and right.

SST
09301-00120  


d.

Evenly tighten the bolts by following the order shown in the illustration.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

C173325

a.

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

Maximum Misalignment:

1.3 mm (0.0512 in.)



b.
C173326E01
2.765,0.477 3.143,0.659 0.378,0.183 10 SST 2.124,1.06 2.55,0.561 false 2.55,0.561 2.734,0.561 false

If the alignment is not as specified, adjust the diaphragm spring tip alignment using SST.

SST
09333-00013  


Hide 31204 4.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

U164587E02
0.365,1.865 1.708,2.094 1.344,0.229 10 true Release hub grease

a.

Apply release hub grease to the release fork, release bearing, push rod contact point and pivot points shown in the illustration.

Grease:

Toyota Genuine Release Hub Grease or equivalent



b.
U164727E02
0.385,1.896 1.729,2.135 1.344,0.24 10 true Clutch spline grease

Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



c.
C163036

Install the release bearing to the clutch release fork with the clip.


d.
C173316

Install the release fork support to the transmission unit.

Torque:
47 N*m (480 kgf*cm, 35 ft.*lbf)


e.

Install the clutch release fork with the clutch release bearing to the transmission unit.

HINT:

After installation, move the fork back and forth to check that the release bearing slides smoothly.



Hide 5.INSTALL MANUAL TRANSMISSION ASSEMBLY