Home › Drivetrain › H150F (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM2660E _52 Drivetrain _052809 H150F MANUAL TRANSMISSION / TRANSAXLE _0255324 OUTPUT SHAFT A

H150F MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 36235B 1.INSTALL NO. 2 TRANSMISSION HUB SLEEVE

C174250E01
0.398,1.277 1.142,1.457 0.744,0.179 10 Front Side

a.

Apply a light coat of gear oil to the No. 2 transmission hub sleeve and No. 2 transmission clutch hub.


b.

Install the No. 2 transmission hub sleeve and 3 shifting keys to the No. 2 transmission clutch hub.

NOTICE:

Do not mistake the installation direction of the No. 2 transmission hub sleeve and No. 2 transmission clutch hub.



c.
C171263

Insert the 2 springs under the shifting keys.

NOTICE:

Position the key springs so that their end gaps are not aligned.



Hide 33395 2.INSTALL NO. 3 TRANSMISSION HUB SLEEVE

C174251E01
0.53,1.272 1.274,1.451 0.744,0.179 10 Front Side

a.

Apply a light coat of gear oil to the No. 3 transmission hub sleeve and No. 3 transmission clutch hub.


b.

Install the No. 3 transmission hub sleeve and 3 shifting keys to the No. 3 transmission clutch hub.

NOTICE:

Do not mistake the installation direction of the No. 3 transmission hub sleeve, No. 3 transmission clutch hub, and shifting keys.



c.
C171263

Insert the 2 springs under the shifting keys.

NOTICE:

Position the key springs so that their end gaps are not aligned.



Hide 33363 3.INSTALL NO. 1 TRANSMISSION HUB SLEEVE

C174252E01
0.376,1.283 1.119,1.462 0.744,0.179 10 Front Side

a.

Apply a light coat of gear oil to the No. 1 transmission hub sleeve and No. 1 transmission clutch hub.


b.

Install the No. 1 transmission hub sleeve and 3 shifting keys to the No. 1 transmission clutch hub.

NOTICE:

Do not mistake the installation direction of the No. 1 transmission hub sleeve and No. 1 transmission clutch hub.



c.
C171263

Insert the 2 springs under the shifting keys.

NOTICE:

Position the key springs so that their end gaps are not aligned.



Hide 33428B 4.INSTALL 5TH COUNTER GEAR BEARING

C174422

a.

Coat the 5th counter gear bearing with gear oil, then install it to the 5th gear.


Hide 33336 5.INSTALL 5TH GEAR

a.

Coat the 5th gear and No. 3 synchronizer ring with gear oil, and set them onto the output shaft.


b.
C171265E01
2.266,0.637 2.635,0.816 0.369,0.179 10 SST 1.848,0.884 2.077,0.718 false 2.077,0.718 2.237,0.718 false

Using SST and a press, install the 5th gear, No. 3 synchronizer ring and transmission hub sleeve to the output shaft.

SST
09316-60011  (09316-00011)

HINT:

Align the convex portion of the synchronizer ring with the groove of the transmission hub sleeve.



c.

Check that the 5th gear, No. 3 synchronizer ring, and transmission hub sleeve move smoothly.


Hide 33393A 6.INSTALL NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING

C171277

a.

Select a new snap ring that will allow minimum clearance.

Standard Clearance:

0.1 mm (0.00393 in.) or less


Snap Ring Thickness:
Part No. Thickness Mark
90520-34018 2.40 to 2.45 mm
(0.0945 to 0.0965 in.)
A
90520-34019 2.45 to 2.50 mm
(0.0965 to 0.0984 in.)
B
90520-34020 2.50 to 2.55 mm
(0.0984 to 0.100 in.)
C
90520-34021 2.55 to 2.60 mm
(0.100 to 0.102 in.)
D
90520-34022 2.60 to 2.65 mm
(0.102 to 0.104 in.)
E
90520-34023 2.65 to 2.70 mm
(0.104 to 0.106 in.)
F



b.
C171266

Using a brass bar and hammer, install the snap ring to the output shaft.


Hide 7.INSTALL 3RD GEAR NEEDLE ROLLER BEARING

C178495

a.

Coat the 3rd gear needle roller bearing with gear oil, and install it to the 3rd gear.


Hide 33333 8.INSTALL 3RD GEAR

a.

Coat the 3rd gear and No. 3 synchronizer ring set with gear oil, and set them onto the output shaft.

HINT:

Align the protrusions of the middle ring of the synchronizer ring set with the notches of the gear.



b.
C171268E01
2.22,0.63 2.580,0.823 0.360,0.193 10 SST 1.849,0.71 2.18,0.71 false

Using SST and a press, install the 3rd gear, No. 3 synchronizer ring set and transmission hub sleeve to the output shaft.

SST
09316-60011  (09316-00011)

HINT:

Align the convex portion of the synchronizer ring with the groove of the transmission hub sleeve.



c.

Check that the 3rd gear, No. 3 synchronizer ring set, and transmission hub sleeve move smoothly.


Hide 33362A 9.INSTALL NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING

C171279

a.

Select a new snap ring that will allow minimum clearance.

Standard Clearance:

0.1 mm (0.00393 in.) or less


Snap Ring Thickness:
Part No. Thickness Mark
90520-28054 1.90 to 1.95 mm
(0.0748 to 0.0768 in.)
4
90520-28055 1.95 to 2.00 mm
(0.0768 to 0.0787 in.)
5
90520-28056 2.00 to 2.05 mm
(0.0787 to 0.0807 in.)
6
90520-28057 2.05 to 2.10 mm
(0.0807 to 0.0827 in.)
7
90520-28058 2.10 to 2.15 mm
(0.0827 to 0.0847 in.)
8
90520-28059 2.15 to 2.20 mm
(0.0847 to 0.0866 in.)
9



b.
C171269

Using a snap ring expander, install the snap ring to the output shaft.


Hide 33332B 10.INSTALL 2ND GEAR NEEDLE ROLLER BEARING

C178496

a.

Coat the 2nd gear needle roller bearing with gear oil, and install it to the output shaft.


Hide 33332 11.INSTALL 2ND GEAR

a.

Coat the 2nd gear and No. 2 synchronizer ring set with gear oil, then install them to the output shaft.

HINT:

Align the protrusions of the middle ring of the synchronizer ring set with the notches of the gear.



b.
C171271

Using a press, install the 2nd gear, No. 2 synchronizer ring set and transmission hub sleeve to the output shaft.

HINT:

Align the convex portion of the synchronizer ring with the groove of the transmission hub sleeve.



c.

Check that the 2nd gear, No. 2 synchronizer ring set, and transmission hub sleeve move smoothly.


Hide 33361B 12.INSTALL NO. 1 CLUTCH HUB SHAFT SNAP RING

C171281

a.

Select a new snap ring that will allow minimum clearance.

Standard Clearance:

0.1 mm (0.00393 in.) or less


Snap Ring Thickness:
Part No. Thickness Mark
90520-46004 2.90 to 2.95 mm
(0.114 to 0.116 in.)
A
90520-46005 2.95 to 3.00 mm
(0.116 to 0.118 in.)
B
90520-46006 3.00 to 3.05 mm
(0.118 to 0.120 in.)
C
90520-46007 3.05 to 3.10 mm
(0.120 to 0.122 in.)
D
90520-46008 3.10 to 3.15 mm
(0.122 to 0.124 in.)
E
90520-46009 3.15 to 3.20 mm
(0.124 to 0.126 in.)
F



b.
C171272

Using a brass bar and a hammer, install the snap ring to the output shaft.


Hide 33335C 13.INSTALL 1ST GEAR NEEDLE ROLLER BEARING

C178497

a.

Coat the 1st gear needle roller bearing with gear oil, and install it to the output shaft.


Hide 33335 14.INSTALL 1ST GEAR

a.

Coat the 1st gear and No. 1 synchronizer ring set with gear oil, and set them onto the output shaft.

HINT:

Align the protrusions of the middle ring of the synchronizer ring set with the notches of the gear.



b.
C174407E01
2.477,0.369 2.848,0.560 0.371,0.191 10 SST 2.336,0.455 2.455,0.455 false 0.629,0.412 1.000,0.603 0.371,0.191 10 SST 1.2,0.503 1.003,0.503 false

Using SST and press, install the 1st gear, No. 1 synchronizer ring set, and output shaft rear bearing to the output shaft.

SST
09316-60011  (09316-00011)
09523-36010  

HINT:
·

Make sure that the groove of the bearing faces the correct direction as shown in the illustration.

·

Align the convex portion of the synchronizer ring with the groove of the transmission hub sleeve.




c.

Check that the transmission hub sleeve, 1st gear and No. 1 synchronizer ring set move smoothly.


Hide 33331B 15.INSTALL REVERSE GEAR SNAP RING

C171286

a.

Select a new snap ring that will allow minimum clearance.

Standard Clearance:

0.1 mm (0.00393 in.) or less


Snap Ring Thickness:
Part No. Thickness Mark
90520-41006 2.40 to 2.45 mm
(0.0945 to 0.0965 in.)
A
90520-41007 2.45 to 2.50 mm
(0.0965 to 0.0984 in.)
B
90520-41008 2.50 to 2.55 mm
(0.0984 to 0.100 in.)
C
90520-41009 2.55 to 2.60 mm
(0.100 to 0.102 in.)
D
90520-41010 2.60 to 2.65 mm
(0.102 to 0.104 in.)
E
90520-41011 2.65 to 2.70 mm
(0.104 to 0.106 in.)
F
90520-41012 2.70 to 2.75 mm
(0.106 to 0.108 in.)
G
90520-41013 2.75 to 2.80 mm
(0.108 to 0.110 in.)
H



b.
C171275

Using a brass bar and a hammer, install the snap ring to the output shaft.


Hide 33336 16.INSPECT 5TH GEAR THRUST CLEARANCE

C171239E07
1.292,0.896 1.292,0.26 1.292,0.26 1.948,0.26 true 2.073,0.156 3.115,0.49 1.042,0.333 10 false 5th Gear Thrust Clearance

a.

Using a feeler gauge, measure the 5th gear thrust clearance.

Standard Clearance:

0.10 to 0.35 mm (0.00394 to 0.0137 in.)


If the clearance is outside the specification, replace the defective gear or shaft.


Hide 33333 17.INSPECT 3RD GEAR THRUST CLEARANCE

C171239E01
1.261,0.123 2.993,0.289 1.732,0.166 10 3rd Gear Thrust Clearance 0.648,0.714 0.648,0.218 false 0.648,0.218 1.222,0.218 false

a.

Using a feeler gauge, measure the 3rd gear thrust clearance.

Standard Clearance:

0.10 to 0.45 mm (0.00394 to 0.0177 in.)


If the clearance is outside the specification, replace the defective gear, transmission clutch hub or shaft.


Hide 33332 18.INSPECT 2ND GEAR THRUST CLEARANCE

C171239E04
0.326,1.741 2.059,1.907 1.732,0.166 10 2nd Gear Thrust Clearance 1.349,1.443 1.349,1.741 false

a.

Using a feeler gauge, measure the 2nd gear thrust clearance.

Standard Clearance:

0.10 to 0.35 mm (0.00394 to 0.0137 in.)


If the clearance is outside the specification, replace the defective gear, transmission clutch hub or shaft.


Hide 33335 19.INSPECT 1ST GEAR THRUST CLEARANCE

C171239E06
2.104,0.792 2.104,0.177 false 2.104,0.177 2.073,0.177 false 0.385,0.094 2.115,0.26 1.729,0.167 10 false 1st Gear Thrust Clearance

a.

Using a feeler gauge, measure the 1st gear thrust clearance.

Standard Clearance:

0.10 to 0.45 mm (0.00394 to 0.0177 in.)


If the clearance is outside the specification, replace the defective gear, transmission clutch hub or shaft.