Coat all of the sliding and rotating surfaces with gear oil before reassembly.
36231
1.INSTALL REAR TRANSFER OUTPUT SHAFT
Install a new needle roller bearing.
Using SST and a press, press in a new bearing.
Set the snap ring groove of the bearing to the front side.
36291A
2.INSTALL TRANSFER DRIVE SPROCKET BEARING
Install the bearing to the output shaft.
36205
3.INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY
Install the drive sprocket to the output shaft.
36231A
4.INSTALL TRANSFER OUTPUT SHAFT SPACER
Install the straight pin to the output shaft.
Align the straight pin with the straight pin groove of the output shaft spacer, and slide on the output shaft spacer.
Using a screwdriver and hammer, tap on the snap ring.
36205
5.INSPECT TRANSFER DRIVE SPROCKET SUB-ASSEMBLY
Using a feeler gauge, measure the drive sprocket thrust clearance.
0.10 to 0.47 mm (0.00394 to 0.0185 in.)
0.47 mm (0.0185 in.)
If the clearance is more than the maximum, replace the drive sprocket sub-assembly.
41311M
6.INSTALL CENTER DIFFERENTIAL CASE
Using SST and a hammer, tap in a new needle roller bearing until its surface is 0 to 0.5 mm (0 to 0.0197 in.) from the center differential case upper surface.
Be careful not to damage the center differential case.
Install the bearing so that the mark is on the outside.
Using SST and a hammer, tap in a new needle roller bearing until its surface is 1.5 to 2.0 mm (0.0591 to 0.0787 in.) from the center differential case upper surface.
Be careful not to damage the center differential case.
Install the bearing so that the mark is on the outside.
for Manual Transmission:
Install the synchromesh shifting key spring and No. 2 synchromesh shifting keys as shown in the illustration.
for Manual Transmission:
Using a snap ring expander, install the snap ring.
Install the center differential case to the output shaft.
36255
7.INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER
Install the straight pin to the output shaft.
Install a new seal ring to the output shaft spacer.
Align the pin with the straight pin groove of the output shaft spacer, and slide on the output shaft spacer.
Using a screwdriver and hammer, tap on the snap ring.
33309H
8.INSTALL TRANSFER OUTPUT SHAFT WASHER
Install the 2 output shaft washers to the output shaft.
36218C
9.INSTALL TRANSFER INPUT SHAFT PLUG
Using SST and a hammer, tap in a new input shaft plug until its surface is 1.0 to 1.8 mm (0.0394 to 0.0709 in.) from the input shaft upper surface.
Be careful not to damage or deform the input shaft plug when tapping it.
36211H
10.INSTALL TRANSFER INPUT SHAFT BIMETAL FORMED BUSH
Using SST and a hammer, tap in a new bush until its surface is 5.5 to 5.9 mm (0.217 to 0.232 in.) from the input shaft upper surface.
Be careful not to damage the input shaft.
36210A
11.INSTALL TRANSFER INPUT SHAFT BEARING
Install the low planetary gear bearing and low planetary gear to the input shaft.
Make sure the low planetary gear bearing is installed in the correct direction.
Install the low planetary gear bearing so that its temper color side faces the low planetary gear.
Install the low planetary gear bearing and a new input shaft bearing to the input shaft.
Make sure the input shaft bearing is installed in the correct direction.
Make sure the low planetary gear bearing is installed in the correct direction.
Install the low planetary gear bearing so that its temper color side faces the low planetary gear.
Using SST and a press, press in the bearing.
After press-fitting the bearing to the input shaft, check that the bearing moves smoothly.
Select a snap ring that allows for minimum axial play and install it to the shaft.
| Mark | Specified Condition |
|---|---|
| C | 2.13 to 2.18 mm (0.0839 to 0.0858 in.) |
| D | 2.18 to 2.23 mm (0.0858 to 0.0878 in.) |
| E | 2.23 to 2.28 mm (0.0878 to 0.0898 in.) |
| F | 2.28 to 2.33 mm (0.0898 to 0.0917 in.) |
| G | 2.33 to 2.38 mm (0.0917 to 0.0937 in.) |
| H | 2.38 to 2.43 mm (0.0937 to 0.0957 in.) |
| J | 2.43 to 2.48 mm (0.0957 to 0.0976 in.) |
Using a snap ring expander, install the snap ring.
Make sure that the snap ring is firmly installed to the groove.
36216A
12.INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING
Apply transfer oil to a new seal ring.
Install a new seal ring to the input shaft.
36292A
13.INSTALL TRANSFER DRIVEN SPROCKET BEARING
Install a new bearing to the front transfer case in the direction shown in the illustration.
Make sure the bearing is installed in the correct direction.
Using a screwdriver, install the snap ring.
36273
14.INSTALL TRANSFER LOW PLANETARY RING GEAR
Using a snap ring expander, install the snap ring to the front transfer case.
Install the low planetary ring gear to the front transfer case.
Make sure to install the low planetary ring gear in the correct direction.
Using a screwdriver, install the snap ring.
Make sure that the snap ring is firmly installed to the groove.
15.INSTALL INPUT SHAFT ASSEMBLY
While expanding the snap ring, install the input shaft to the front transfer case.
Apply adhesive to the threads of the 2 case plugs.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the plugs within 3 minutes of application.
Using a 14 mm hexagon wrench, install the 2 case plugs.
33449D
16.INSTALL TRANSFER CASE MAGNET
Install the magnet to the oil separator.
36104K
17.INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY
Install a new O-ring to the oil separator.
Install the oil separator with the 3 bolts.
41335D
18.INSTALL SIDE GEAR SHAFT HOLDER BEARING
Using SST and a hammer, tap in a new bearing to the rear transfer case.
Using a screwdriver, install the snap ring.
36236
19.INSTALL FRONT DRIVE CLUTCH SLEEVE
Apply gear oil to the connecting areas of the clutch sleeve and center differential case.
Install the clutch sleeve onto the output shaft.
Make sure that the clutch sleeve is installed facing the correct direction.
20.INSTALL REAR TRANSFER OUTPUT SHAFT ASSEMBLY
Install the snap ring to the rear transfer case.
Install the output shaft, drive chain and driven sprocket.
Do not drop the output shaft washers.
Using a snap ring expander, install the snap ring to the output shaft.
Make sure that the snap ring is firmly installed to the groove.
36410J
21.INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY
Install a new O-ring to the shift actuator.
Set the No. 1 gear shift fork to the front drive clutch sleeve.
Install the shift actuator to the rear transfer case with the 3 bolts.
Install the No. 1 gear shift fork to the shift actuator with the bolt.
36312F
22.INSTALL NO. 2 TRANSFER GEAR SHIFT FORK
Set the No. 2 gear shift fork together with the high and low clutch sleeve to the shift actuator.
Install the No. 2 gear shift fork to the shift actuator with the bolt.
Using a screwdriver and hammer, tap the 4 shift fork shaft snap rings onto the shift fork shaft.
36231E
23.INSTALL FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING
Install the needle roller bearing to the output shaft.
33367F
24.INSTALL NO. 1 SYNCHRONIZER RING (for Manual Transmission)
Align the protrusion of the synchronizer ring with the notch on the differential case and install it.
36112
25.INSTALL REAR TRANSFER CASE ASSEMBLY
Apply seal packing to the rear transfer case as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
If the removed rear transfer case will be reused: After removing the rear transfer case, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the rear transfer case contact surface, 2) clean off any remaining old FIPG from the rear transfer case contact surface, and 3) reapply seal packing to the rear transfer case.
Install the rear transfer case with the 14 bolts.
Tighten the bolts within 10 minutes of applying the seal packing. The seal packing will dry very quickly.
36113C
26.INSTALL TRANSFER CASE PLUG
Apply adhesive to the threads of the plug.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the plug within 3 minutes of application.
Using a 6 mm hexagon wrench, install the plug.
36114B
27.INSTALL NO. 1 TRANSFER CASE PLUG
Install the pin and compression spring to the front transfer case.
Apply adhesive to the threads of the plug.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the plug within 3 minutes of application.
Install the plug.
36115C
28.INSTALL TRANSFER CASE REAR OIL SEAL
33309C
29.INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
Install the companion flange onto the output shaft.
Using SST to hold the companion flange, install a new O-ring and a new companion flange lock nut.
Using a chisel and hammer, stake the companion flange lock nut.
36102J
30.INSTALL TRANSFER CASE FRONT OIL SEAL
36104B
31.INSTALL TRANSFER OUTPUT SHAFT DUST DEFLECTOR
Using SST and a press, install a new transfer output shaft dust deflector.
Be careful not to damage the transfer output shaft dust deflector and front output shaft companion flange sub-assembly.
The transfer output shaft dust deflector should be installed completely.
Apply MP grease to the transfer output shaft dust deflector lip.
0.4 to 0.6 g (0.015 to 0.021 oz.)
0.1 g (0.0004 oz.)
33309C
32.INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
Install the companion flange onto the drive sprocket.
Using SST to hold the companion flange, install a new O-ring and a new companion flange lock nut.
Using a chisel and hammer, stake the companion flange lock nut.
36111B
33.INSTALL TRANSFER OIL PUMP PLATE OIL SEAL
Using SST and a hammer, tap in a new oil seal until its surface is flush with the oil pump plate upper surface.
Be careful not to damage the oil pump plate.
36111F
34.INSTALL TRANSFER CASE PLUG
Install the relief valve seat, ball and compression spring to the oil pump plate.
Apply adhesive to the threads of the plug.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the plug within 3 minutes of application.
Using a 10 mm hexagon wrench, install the plug.
36111G
35.INSTALL TRANSFER CASE STRAIGHT PIN
Install the 2 straight pins to the input shaft.
36183A
36.INSTALL TRANSFER OIL PUMP PLATE
Apply transfer oil to a new O-ring, drive rotor, driven rotor and a new transfer oil seal ring.
Install the drive rotor to the input shaft.
Install the transfer oil seal ring to the input shaft.
Install the O-ring to the oil pump plate.
Install the oil pump plate and driven rotor to the front transfer case with the 4 bolts.
37109A
37.INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY
Install the bracket to the rear transfer case with the bolt.