Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255336 TRANSFER ASSEMBLY A

JF2A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Coat all of the sliding and rotating surfaces with gear oil before reassembly.


PROCEDURE

Hide 36231 1.INSTALL REAR TRANSFER OUTPUT SHAFT

a.
C173615

Install a new needle roller bearing.


b.
C173617E01
0.093,1.545 0.468,1.774 0.375,0.229 10 SST 0.678,2.182 0.605,1.618 false 0.605,1.618 0.471,1.618 false

Using SST and a press, press in a new bearing.

SST
09527-10011  

NOTICE:

Set the snap ring groove of the bearing to the front side.



Hide 36291A 2.INSTALL TRANSFER DRIVE SPROCKET BEARING

a.
C173614

Install the bearing to the output shaft.


Hide 36205 3.INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

a.
C173613

Install the drive sprocket to the output shaft.


Hide 36231A 4.INSTALL TRANSFER OUTPUT SHAFT SPACER

a.
C173612E01
0.452,0.301 1.228,0.489 0.776,0.188 10 Straight Pin 1.941,1.088 1.669,0.39 false 1.672,0.391 1.396,0.391 false

Install the straight pin to the output shaft.


b.
C173621

Align the straight pin with the straight pin groove of the output shaft spacer, and slide on the output shaft spacer.


c.
C173625

Using a screwdriver and hammer, tap on the snap ring.


Hide 36205 5.INSPECT TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

a.
C173640

Using a feeler gauge, measure the drive sprocket thrust clearance.

Standard Clearance:

0.10 to 0.47 mm (0.00394 to 0.0185 in.)


Maximum Clearance:

0.47 mm (0.0185 in.)


If the clearance is more than the maximum, replace the drive sprocket sub-assembly.


Hide 41311M 6.INSTALL CENTER DIFFERENTIAL CASE

a.
C173618E01
2.85,0.763 3.152,0.919 0.302,0.156 10 SST 2.577,1.057 2.79,0.842 false 2.79,0.842 2.653,1.239 false

Using SST and a hammer, tap in a new needle roller bearing until its surface is 0 to 0.5 mm (0 to 0.0197 in.) from the center differential case upper surface.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)

NOTICE:
·

Be careful not to damage the center differential case.

·

Install the bearing so that the mark is on the outside.




b.
C173619E01
2.932,0.987 3.242,1.176 0.310,0.189 10 SST 2.661,1.227 2.88,1.064 false 2.88,1.064 2.726,1.39 false

Using SST and a hammer, tap in a new needle roller bearing until its surface is 1.5 to 2.0 mm (0.0591 to 0.0787 in.) from the center differential case upper surface.

SST
09950-60010  (09951-00460)
09950-70010  (09951-07100)

NOTICE:
·

Be careful not to damage the center differential case.

·

Install the bearing so that the mark is on the outside.




c.
C173620E03
1.396,0.688 1.771,0.115 false 1.771,0.104 2.229,0.104 false 1.75,0.927 2.229,1.063 false 2.229,1.063 1.75,1.188 false 2.281,0.042 3.198,0.51 0.917,0.469 10 false Synchromesh Shifting Key Spring 2.281,0.979 3.188,1.5 0.906,0.521 10 false No. 2 Synchromesh Shifting Key

for Manual Transmission:

Install the synchromesh shifting key spring and No. 2 synchromesh shifting keys as shown in the illustration.


d.
C173607

for Manual Transmission:

Using a snap ring expander, install the snap ring.


e.
C173606

Install the center differential case to the output shaft.


Hide 36255 7.INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER

a.
C173605E01
0.254,0.409 0.906,0.749 0.652,0.340 10 Straight Pin 1.385,1.041 1.124,0.497 false 1.124,0.497 0.908,0.497 false

Install the straight pin to the output shaft.


b.
C173604

Install a new seal ring to the output shaft spacer.


c.
C173622

Align the pin with the straight pin groove of the output shaft spacer, and slide on the output shaft spacer.


d.
C173624

Using a screwdriver and hammer, tap on the snap ring.


Hide 33309H 8.INSTALL TRANSFER OUTPUT SHAFT WASHER

a.
C173600

Install the 2 output shaft washers to the output shaft.


Hide 36218C 9.INSTALL TRANSFER INPUT SHAFT PLUG

a.
C173497E01
2.936,2.304 3.242,2.484 0.305,0.180 10 SST 2.78,2.03 3.08,2.286 false 3.08,2.286 2.662,1.552 false

Using SST and a hammer, tap in a new input shaft plug until its surface is 1.0 to 1.8 mm (0.0394 to 0.0709 in.) from the input shaft upper surface.

SST
09950-60010  (09951-00410)
09950-70010  (09951-07150)

NOTICE:

Be careful not to damage or deform the input shaft plug when tapping it.



Hide 36211H 10.INSTALL TRANSFER INPUT SHAFT BIMETAL FORMED BUSH

a.
C173632E01
2.791,0.778 3.107,0.972 0.316,0.194 10 SST 2.556,1.043 2.734,0.853 false 2.734,0.853 2.635,1.276 false

Using SST and a hammer, tap in a new bush until its surface is 5.5 to 5.9 mm (0.217 to 0.232 in.) from the input shaft upper surface.

SST
09950-70010  (09951-07150)
09950-60010  (09951-00610)

NOTICE:

Be careful not to damage the input shaft.



Hide 36210A 11.INSTALL TRANSFER INPUT SHAFT BEARING

a.
C173499E01
0.561,0.656 1.909,0.830 1.347,0.174 10 Temper Color Side 2.308,0.748 2.055,0.748 false

Install the low planetary gear bearing and low planetary gear to the input shaft.

NOTICE:
·

Make sure the low planetary gear bearing is installed in the correct direction.

·

Install the low planetary gear bearing so that its temper color side faces the low planetary gear.




b.
C173498E01
1.722,1.076 2.954,1.258 1.232,0.182 10 Temper Color Side 2.409,0.715 2.409,1.016 false

Install the low planetary gear bearing and a new input shaft bearing to the input shaft.

NOTICE:
·

Make sure the input shaft bearing is installed in the correct direction.

·

Make sure the low planetary gear bearing is installed in the correct direction.

·

Install the low planetary gear bearing so that its temper color side faces the low planetary gear.




c.
C173500E01
1.7,2.778 2.086,3.123 0.386,0.346 1.719,2.797 2.037,2.957 0.318,0.161 10 SST 2.985,0.542 3.303,0.702 0.318,0.161 10 SST 2.805,0.827 2.86,0.621 false 2.86,0.621 2.955,0.621 false 2.254,2.894 2.065,2.894 false

Using SST and a press, press in the bearing.

SST
09513-36040  
09515-21010  

NOTICE:

After press-fitting the bearing to the input shaft, check that the bearing moves smoothly.



d.
C173626

Select a snap ring that allows for minimum axial play and install it to the shaft.

Standard Snap Ring Thickness:
Mark Specified Condition
C 2.13 to 2.18 mm (0.0839 to 0.0858 in.)
D 2.18 to 2.23 mm (0.0858 to 0.0878 in.)
E 2.23 to 2.28 mm (0.0878 to 0.0898 in.)
F 2.28 to 2.33 mm (0.0898 to 0.0917 in.)
G 2.33 to 2.38 mm (0.0917 to 0.0937 in.)
H 2.38 to 2.43 mm (0.0937 to 0.0957 in.)
J 2.43 to 2.48 mm (0.0957 to 0.0976 in.)



e.

Using a snap ring expander, install the snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 36216A 12.INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING

C173492E01
2.455,0.334 3.094,0.556 0.639,0.222 10 Seal Ring 2.047,0.682 2.233,0.416 false 2.233,0.416 2.404,0.416 false

a.

Apply transfer oil to a new seal ring.


b.

Install a new seal ring to the input shaft.


Hide 36292A 13.INSTALL TRANSFER DRIVEN SPROCKET BEARING

a.
C162208

Install a new bearing to the front transfer case in the direction shown in the illustration.

NOTICE:

Make sure the bearing is installed in the correct direction.



b.
C173489

Using a screwdriver, install the snap ring.


Hide 36273 14.INSTALL TRANSFER LOW PLANETARY RING GEAR

a.
C174065

Using a snap ring expander, install the snap ring to the front transfer case.


b.
C173496E01
0.719,0.101 1.101,0.279 0.382,0.178 10 Front

Install the low planetary ring gear to the front transfer case.

NOTICE:

Make sure to install the low planetary ring gear in the correct direction.



c.
C173488

Using a screwdriver, install the snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 15.INSTALL INPUT SHAFT ASSEMBLY

a.
C176062

While expanding the snap ring, install the input shaft to the front transfer case.


b.

Apply adhesive to the threads of the 2 case plugs.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Install the plugs within 3 minutes of application.



c.
C159719

Using a 14 mm hexagon wrench, install the 2 case plugs.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33449D 16.INSTALL TRANSFER CASE MAGNET

a.
C174062

Install the magnet to the oil separator.


Hide 36104K 17.INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY

a.

Install a new O-ring to the oil separator.


b.
C173486

Install the oil separator with the 3 bolts.

Torque:
18 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 41335D 18.INSTALL SIDE GEAR SHAFT HOLDER BEARING

a.
C176193E01
1.964,1.475 2.328,1.640 0.364,0.165 10 SST 2.53,1.738 2.332,1.562 false 2.332,1.562 2.465,1.894 false

Using SST and a hammer, tap in a new bearing to the rear transfer case.

SST
09950-60010  (09951-00590)
09950-70010  (09951-07100)


b.
C160519

Using a screwdriver, install the snap ring.


Hide 36236 19.INSTALL FRONT DRIVE CLUTCH SLEEVE

C174060E01
1.199,0.659 1.614,0.849 0.414,0.189 10 Front

a.

Apply gear oil to the connecting areas of the clutch sleeve and center differential case.


b.

Install the clutch sleeve onto the output shaft.

NOTICE:

Make sure that the clutch sleeve is installed facing the correct direction.



Hide 20.INSTALL REAR TRANSFER OUTPUT SHAFT ASSEMBLY

a.
C174066

Install the snap ring to the rear transfer case.


b.
C175996E01
0.902,1.79 1.821,1.960 0.919,0.170 10 Output Shaft 0.213,0.191 1.127,0.420 0.914,0.229 10 Drive Chain 2.669,0.301 3.258,0.703 0.590,0.402 10 Driven Sprocket 0.699,1.753 0.648,1.87 false 0.648,1.87 0.857,1.87 false 1.576,0.756 1.481,0.286 false 1.481,0.286 1.172,0.286 false 2.279,1.538 2.389,0.378 false 2.389,0.378 2.633,0.378 false

Install the output shaft, drive chain and driven sprocket.

NOTICE:

Do not drop the output shaft washers.



c.
C173484

Using a snap ring expander, install the snap ring to the output shaft.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 36410J 21.INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY

a.
C160356E05
2.375,0.781 2.656,0.781 false 2.708,0.698 3.292,1.135 0.583,0.438 10 true O-Ring

Install a new O-ring to the shift actuator.


b.
U165154E02
2.219,0.563 2.042,0.271 false 2.042,0.271 1.594,0.271 false 0.813,2.583 1.813,2.958 1,0.375 10 false No. 1 Transfer Gear Shift Fork 0.698,0.198 1.615,0.396 0.917,0.198 10 false Shift Actuator

Set the No. 1 gear shift fork to the front drive clutch sleeve.


c.
C173374

Install the shift actuator to the rear transfer case with the 3 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.
C173373

Install the No. 1 gear shift fork to the shift actuator with the bolt.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 36312F 22.INSTALL NO. 2 TRANSFER GEAR SHIFT FORK

a.
C174533E01
1.935,0.558 2.327,0.742 0.392,0.184 10 Front

Set the No. 2 gear shift fork together with the high and low clutch sleeve to the shift actuator.


b.
C173339

Install the No. 2 gear shift fork to the shift actuator with the bolt.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


c.
C175998

Using a screwdriver and hammer, tap the 4 shift fork shaft snap rings onto the shift fork shaft.


Hide 36231E 23.INSTALL FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING

a.
C404872E01
0.469,1.531 0.667,0.417 0.667,0.417 0.917,0.417 true 1.021,0.302 2.125,0.729 1.104,0.427 10 false Needle Roller Bearing

Install the needle roller bearing to the output shaft.


Hide 33367F 24.INSTALL NO. 1 SYNCHRONIZER RING (for Manual Transmission)

C173623

a.

Align the protrusion of the synchronizer ring with the notch on the differential case and install it.


Hide 36112 25.INSTALL REAR TRANSFER CASE ASSEMBLY

a.
C173596E01
1.309,1.696 2.243,1.912 0.934,0.216 10 Seal Packing 1.205,1.343 1.052,1.776 false 1.052,1.776 1.241,1.776 false

Apply seal packing to the rear transfer case as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

If the removed rear transfer case will be reused: After removing the rear transfer case, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the rear transfer case contact surface, 2) clean off any remaining old FIPG from the rear transfer case contact surface, and 3) reapply seal packing to the rear transfer case.



b.
C173337

Install the rear transfer case with the 14 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:

Tighten the bolts within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



Hide 36113C 26.INSTALL TRANSFER CASE PLUG

a.

Apply adhesive to the threads of the plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Install the plug within 3 minutes of application.



b.
C173336

Using a 6 mm hexagon wrench, install the plug.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 36114B 27.INSTALL NO. 1 TRANSFER CASE PLUG

a.
C176791

Install the pin and compression spring to the front transfer case.


b.

Apply adhesive to the threads of the plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Install the plug within 3 minutes of application.



c.

Install the plug.

Torque:
19 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 33309C 29.INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.

Install the companion flange onto the output shaft.


b.
C173334E04
1.885,0.635 2.292,1.323 true 2.292,1.323 2.563,1.323 false 2.604,1.229 2.938,1.438 0.333,0.208 10 false SST

Using SST to hold the companion flange, install a new O-ring and a new companion flange lock nut.

SST
09330-00021  

Torque:
112 N*m (1137 kgf*cm, 82 ft.*lbf)


c.
C174574E01
1.258,0 2.043,0.179 0.785,0.179 10 CORRECT 1.209,1.588 2.295,1.767 1.086,0.179 10 INCORRECT

Using a chisel and hammer, stake the companion flange lock nut.


Hide 36104B 31.INSTALL TRANSFER OUTPUT SHAFT DUST DEFLECTOR

a.
C284227E01
1.017,0.126 0.428,0.487 0.428,0.487 0.897,0.771 false 0.879,0.44 0.428,0.487 false 0.059,0.41 0.416,0.569 0.357,0.159 10 SST

Using SST and a press, install a new transfer output shaft dust deflector.

SST
09523-36010  
09950-60010  (09951-00460, 09951-00560, 09952-06010)
09950-70010  (09951-07100)

NOTICE:
·

Be careful not to damage the transfer output shaft dust deflector and front output shaft companion flange sub-assembly.

·

The transfer output shaft dust deflector should be installed completely.




b.
C285650E01
2.125,0.385 2.365,0.583 0.24,0.198 10 true (A) 0.927,0.479 1.167,0.677 0.24,0.198 10 false (B)

Apply MP grease to the transfer output shaft dust deflector lip.

Standard Grease Capacity:
Location A:

0.4 to 0.6 g (0.015 to 0.021 oz.)

Location B:

0.1 g (0.0004 oz.)



Hide 33309C 32.INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.

Install the companion flange onto the drive sprocket.


b.
C173331E01
2.856,0.553 3.225,0.751 0.369,0.198 10 SST 2.169,1.078 2.631,0.638 false 2.631,0.638 2.812,0.638 false

Using SST to hold the companion flange, install a new O-ring and a new companion flange lock nut.

SST
09330-00021  

Torque:
112 N*m (1137 kgf*cm, 82 ft.*lbf)


c.
C174574E01
1.258,0 2.043,0.179 0.785,0.179 10 CORRECT 1.209,1.588 2.295,1.767 1.086,0.179 10 INCORRECT

Using a chisel and hammer, stake the companion flange lock nut.


Hide 36111B 33.INSTALL TRANSFER OIL PUMP PLATE OIL SEAL

a.
C173597E01
1.064,0.307 1.415,0.477 0.350,0.170 10 SST 1.944,0.525 1.477,0.376 false 1.477,0.376 1.811,0.728 false

Using SST and a hammer, tap in a new oil seal until its surface is flush with the oil pump plate upper surface.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07100)

NOTICE:

Be careful not to damage the oil pump plate.



Hide 36111F 34.INSTALL TRANSFER CASE PLUG

a.
C177450

Install the relief valve seat, ball and compression spring to the oil pump plate.


b.

Apply adhesive to the threads of the plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Install the plug within 3 minutes of application.



c.

Using a 10 mm hexagon wrench, install the plug.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 36111G 35.INSTALL TRANSFER CASE STRAIGHT PIN

a.
C162213E04
2.125,0.219 1.417,0.219 false 1.417,1.479 1.417,0.219 false 1.865,1.563 1.865,0.49 false 1.865,0.49 1.417,0.49 false 2.135,0.063 3.104,0.438 0.969,0.375 10 false Transfer Case Straight Pin

Install the 2 straight pins to the input shaft.


Hide 36183A 36.INSTALL TRANSFER OIL PUMP PLATE

a.

Apply transfer oil to a new O-ring, drive rotor, driven rotor and a new transfer oil seal ring.


b.
C173598E06
1.76,0.677 2.031,0.448 false 2.031,0.448 2.344,0.448 false 2.385,0.344 3.26,1.156 0.875,0.813 10 true Oil Pump Drive Rotor

Install the drive rotor to the input shaft.


c.
C173490

Install the transfer oil seal ring to the input shaft.


d.

Install the O-ring to the oil pump plate.


e.
C159613

Install the oil pump plate and driven rotor to the front transfer case with the 4 bolts.

Torque:
12 N*m (117 kgf*cm, 9 ft.*lbf)


Hide 37109A 37.INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY

a.
C174577

Install the bracket to the rear transfer case with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)