Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY › 2014.08–2015.08
RM2660E _52 Drivetrain _052812 AXLE AND DIFFERENTIAL _0255357 FRONT DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 41111D 1.INSTALL FRONT DIFFERENTIAL CARRIER STRAIGHT PIN

a.
C176514E04
3,0.906 3.177,1.177 0.177,0.271 10 false a

Using a plastic-faced hammer, tap in the straight pins until the protrusion height shown in the illustration is within the specification.

Standard height (a):

9.5 to 10.0 mm (0.374 to 0.394 in.)



Hide 41320C 2.INSTALL FRONT DIFFERENTIAL TUBE STRAIGHT PIN

a.
C176515E04
3.031,0.885 3.208,1.156 0.177,0.271 10 false a

Using a plastic-faced hammer, tap in the straight pins until the protrusion height shown in the illustration is within the specification.

Standard height (a):

9.5 to 10.0 mm (0.374 to 0.394 in.)



Hide 41304L 3.INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING

a.
R101722E01
1.833,0.844 2.427,0.844 false 2.5,0.76 2.958,0.958 0.458,0.198 10 false SST

Using SST and a press, press in the bearing.

SST
09223-00010  


b.
C171954

Using a snap ring expander, install a new snap ring.


Hide 41304F 4.INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

a.
C159248

Install the side gear shaft into the differential tube.


b.

Using snap ring pliers, install a new snap ring.


Hide 41304P 5.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
C159268E04
2.208,0.875 2.417,1.208 2.417,1.208 2.531,1.208 false 2.594,1.135 2.969,1.302 0.375,0.167 10 false SST

Using SST and a plastic-faced hammer, tap in a new oil seal.

SST
09608-32010  

Standard oil seal depth:

4.8 to 5.8 mm (0.189 to 0.228 in.)



b.

Coat the lip of the oil seal with MP grease.


Hide 41301L 6.INSTALL FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

a.
FA01121

Install the 2 side gear thrust washers onto the 2 side gears.


b.

Install the 2 side gears (with thrust washers), 2 pinion gears, 2 pinion gear thrust washers and pinion shaft into the differential case assembly.

HINT:
·

Align the holes of the differential case assembly and pinion shaft.

·

Apply hypoid gear oil to each sliding surface and rotating part.




c.

Measure the side gear backlash.

i.
F043636

Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case assembly.

Standard backlash:

0.1 to 0.25 mm (0.00394 to 0.00984 in.)


If the backlash is not within the specification, replace the 2 side gear thrust washers. Use the table below to select 2 thrust washers of the same thickness which will ensure that the backlash is within the specification.

Standard Washer Thickness:
Specified Condition Specified Condition
1.43 to 1.47 mm (0.0563 to 0.0578 in.) 1.68 to 1.72 mm (0.0662 to 0.0677 in.)
1.48 to 1.52 mm (0.0583 to 0.0598 in.) 1.73 to 1.77 mm (0.0682 to 0.0696 in.)
1.53 to 1.57 mm (0.0603 to 0.0618 in.) 1.78 to 1.82 mm (0.0701 to 0.0716 in.)
1.58 to 1.62 mm (0.0622 to 0.0637 in.) 1.83 to 1.87 mm (0.0721 to 0.0736 in.)
1.63 to 1.67 mm (0.0642 to 0.0657 in.) -




d.
FA01124

Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the pinion shaft.


e.

Stake the differential case.


Hide 7.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the differential case and ring gear.


b.

Heat the ring gear to about 100°C (212°F) in boiling water.


c.

Carefully take the ring gear out of the boiling water.


d.

After the moisture on the ring gear has completely evaporated, quickly align the matchmarks on the ring gear and differential case and set the ring gear onto the differential case. Then temporarily install the 12 bolts so that the bolt holes in the ring gear and differential case are aligned.


e.

After the ring gear cools down sufficiently, remove the 12 bolts. Then apply adhesive to the 12 bolts and install them.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent



Hide 41311A 8.INSTALL FRONT DIFFERENTIAL CASE BEARING

a.
C159256E02
0.541,0.865 0.958,1.343 false 0.955,1.106 0.732,0.864 0.732,0.864 0.473,0.864 false 0.131,0.787 0.431,0.980 0.299,0.193 10 SST

Using SST and a press, press in the 2 bearings (inner race).

SST
09316-20011  
09316-60011  (09316-00041)


Hide 41311A 9.INSTALL FRONT DIFFERENTIAL CASE BEARING

HINT:

When replacing the 2 differential case bearings, fit the thinnest washer to each bearing. When reusing the bearings, fit a washer of the same thickness as the one removed to each bearing.


a.
U156096E02
0.875,0.677 1.229,1.146 true 1.271,0.948 1.063,0.677 1.063,0.677 0.833,0.677 true 0.542,0.604 0.917,0.802 0.375,0.198 10 false SST 2.042,0.115 2.219,0.271 0.177,0.156 10 false *1

Install a new plate washer to the shaft bearing retainer.

Text in Illustration
*1 Plate Washer


b.

Using SST and a press, press the bearing (outer race) into the differential case bearing retainer.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


c.
U156097E02
1.406,0.563 1.073,1.458 true 0.99,1.135 1.208,0.573 1.208,0.573 1.479,0.573 true 2.458,0.813 1.875,0.188 1.875,0.188 1.802,0.188 true 1.521,0.49 1.896,0.688 0.375,0.198 10 false SST 1.625,0.125 1.802,0.281 0.177,0.156 10 false *1

Install a new plate washer to the differential carrier.

Text in Illustration
*1 Plate Washer


d.

Using SST and a press, press the bearing (outer race) into the differential carrier assembly.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


Hide 41211B 10.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING

a.
U156098E01
0.907,1.946 1.525,1.946 1.525,1.946 1.729,2.179 false 1.168,2.174 1.018,1.948 false 0.549,1.865 0.883,2.030 0.334,0.165 10 SST

Using SST, install the bearing (outer race).

SST
09950-60020  (09951-00810, 09951-00890)


Hide 41211A 11.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
U156099E02
0.948,1.948 1.823,1.948 1.823,1.948 2.031,2.24 true 1.146,2.156 1.042,1.948 true 1.313,2.875 1.427,3.063 1.427,3.063 1.51,3.063 true 0.583,1.854 0.917,2.01 0.333,0.156 10 false SST 1.552,2.979 1.729,3.135 0.177,0.156 10 false *1

Using SST, install the washer and bearing (outer race).

SST
09950-60020  (09951-00890, 09951-01030)

Text in Illustration
*1 Plate Washer

HINT:

After installing the washer, check the tooth contact pattern. If necessary, replace the washer with one of a different thickness.



Hide 41211A 12.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C159255E04
0.917,0.979 1.094,0.979 1.094,0.979 1.438,1.5 true 0.552,0.896 0.885,1.063 0.333,0.167 10 false SST

Using SST and a press, press in the bearing (inner race).

SST
09506-35010  


Hide 41110V 13.INSTALL FRONT DIFFERENTIAL UNION

a.
C159447

Install the front differential union to the differential carrier.


Hide 41183C 14.INSTALL FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR

a.
C159446

Install the 2 bolts and oil deflector.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 15.TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION

Hide 41301L 16.INSTALL FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 41141L 17.INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

a.
C160133E01
2.303,0.58 2.441,0.750 0.139,0.170 10 A 1.4,0.626 1.539,0.795 0.139,0.170 10 A 0.919,0.767 1.058,0.937 0.139,0.170 10 A 0.524,0.918 0.662,1.088 0.139,0.170 10 A 2.909,1.068 3.047,1.238 0.139,0.170 10 A 3.012,1.569 3.150,1.739 0.139,0.170 10 A 1.389,2.706 1.528,2.876 0.139,0.170 10 A 1.018,2.442 1.156,2.612 0.139,0.170 10 A 0.832,2.235 0.970,2.405 0.139,0.170 10 A 0.623,2.067 0.761,2.237 0.139,0.170 10 A 0.142,1.907 0.281,2.076 0.139,0.170 10 A 2.976,1.927 3.229,2.096 0.253,0.170 10 B 2.71,2.704 2.963,2.874 0.253,0.170 10 B 2.311,2.775 2.564,2.944 0.253,0.170 10 B

Install the differential cross shaft bearing retainer and differential support with the 14 bolts.

Torque:
for bolt A : 65 N*m (663 kgf*cm, 48 ft.*lbf)
for bolt B : 155 N*m (1581 kgf*cm, 114 ft.*lbf)


Hide 41211B 18.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING

a.
C159445E03
2.594,1.396 2.469,1.396 2.469,1.396 2.188,1.073 false 2.646,1.313 2.979,1.479 0.333,0.167 10 false SST

Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

SST
09316-60011  (09316-00041)


Hide 41214C 19.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 20.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C358635E02
1.094,0.365 1.292,0.365 1.292,0.365 1.51,0.604 false 0.771,0.313 1.229,0.51 0.458,0.198 10 false SST 0.594,1.521 1.052,1.719 0.458,0.198 10 false *b 2.688,0.792 3.083,0.99 0.396,0.198 10 false *a

Using SST, install the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

Text in Illustration
*a Turn
*b Hold


b.

Coat the threads of the nut with hypoid gear oil.


c.
C159272E02
0.338,0.534 0.653,0.676 0.316,0.142 10 SST 0.717,0.618 0.876,0.618 0.876,0.618 1.152,0.747 false

Using SST to hold the companion flange in place, then slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).

SST
09330-00021  (09330-00030)

Limit Torque Value:

451 N*m (4599 kgf*cm, 332ft.*lbf) or less


NOTICE:

As there is no spacer, tighten the nut a little at a time, being careful not to overtighten it.



d.
C358623

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard Preload (at Starting):
Bearing Specified Condition
New 2.97 to 3.47 N*m (31 to 35 kgf*cm, 27 to 30 in.*lbf)
Reused 2.14 to 2.45 N*m (22 to 24 kgf*cm, 19 to 21 in.*lbf)


If necessary, disassemble and inspect the differential assembly.


Hide 21.ADJUST BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION

a.
C159798E03
1.615,1.125 1.073,0.854 1.073,0.854 0.844,0.854 true 0.49,0.771 0.948,0.979 0.458,0.208 10 false SST

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-33010  

Standard backlash:

0.17 to 0.27 mm (0.00670 to 0.0106 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

HINT:
·

There should be no clearance between the plate washer and differential case.

·

Make sure that there is ring gear backlash.



Standard Washer Thickness:
Specified Condition Specified Condition
1.49 to 1.51 mm (0.0587 to 0.0594 in.) 1.93 to 1.95 mm (0.0760 to 0.0767 in.)
1.51 to 1.53 mm (0.0595 to 0.0602 in.) 1.95 to 1.97 mm (0.0768 to 0.0775 in.)
1.53 to 1.55 mm (0.0603 to 0.0610 in.) 1.97 to 1.99 mm (0.0776 to 0.0783 in.)
1.55 to 1.57 mm (0.0610 to 0.0618 in.) 1.99 to 2.01 mm (0.0784 to 0.0791 in.)
1.57 to 1.59 mm (0.0619 to 0.0625 in.) 2.01 to 2.03 mm (0.0792 to 0.0799 in.)
1.59 to 1.61 mm (0.0626 to 0.0633 in.) 2.03 to 2.05 mm (0.0800 to 0.0807 in.)
1.61 to 1.63 mm (0.0634 to 0.0641 in.) 2.05 to 2.07 mm (0.0808 to 0.0814 in.)
1.63 to 1.65 mm (0.0642 to 0.0649 in.) 2.07 to 2.09 mm (0.0815 to 0.0822 in.)
1.65 to 1.67 mm (0.0650 to 0.0657 in.) 2.09 to 2.11 mm (0.0823 to 0.0830 in.)
1.67 to 1.69 mm (0.0658 to 0.0665 in.) 2.11 to 2.13 mm (0.0831 to 0.0838 in.)
1.69 to 1.71 mm (0.0666 to 0.0673 in.) 2.13 to 2.15 mm (0.0839 to 0.0846 in.)
1.71 to 1.73 mm (0.0674 to 0.0681 in.) 2.15 to 2.17 mm (0.0847 to 0.0854 in.)
1.73 to 1.75 mm (0.0682 to 0.0688 in.) 2.17 to 2.19 mm (0.0855 to 0.0862 in.)
1.75 to 1.77 mm (0.0689 to 0.0696 in.) 2.19 to 2.21 mm (0.0863 to 0.0870 in.)
1.77 to 1.79 mm (0.0697 to 0.0704 in.) 2.21 to 2.23 mm (0.0871 to 0.0877 in.)
1.79 to 1.81 mm (0.0705 to 0.0712 in.) 2.23 to 2.25 mm (0.0878 to 0.0885 in.)
1.81 to 1.83 mm (0.0713 to 0.0720 in.) 2.25 to 2.27 mm (0.0886 to 0.0893 in.)
1.83 to 1.85 mm (0.0720 to 0.0728 in.) 2.27 to 2.29 mm (0.0894 to 0.0901 in.)
1.85 to 1.87 mm (0.0729 to 0.0736 in.) 2.29 to 2.31 mm (0.0902 to 0.0909 in.)
1.87 to 1.89 mm (0.0737 to 0.0744 in.) 2.31 to 2.33 mm (0.0910 to 0.0917 in.)
1.89 to 1.91 mm (0.0745 to 0.0751 in.) 2.33 to 2.35 mm (0.0918 to 0.0925 in.)
1.91 to 1.93 mm (0.0752 to 0.0759 in.) -



Hide 22.INSPECT TOTAL PRELOAD

a.
C358623

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Total Preload (at Starting):
Bearing Specified Condition
New 4.58 to 5.88 N*m (47 to 59 kgf*cm, 41 to 52 in.*lbf)
Reused 3.47 to 4.58 N*m (36 to 46 kgf*cm, 31 to 40 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 23.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.

Remove the bearing retainer and differential case.


b.
R013220

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


c.

Install the differential case to the differential carrier.


d.
C160133E01
2.303,0.58 2.441,0.750 0.139,0.170 10 A 1.4,0.626 1.539,0.795 0.139,0.170 10 A 0.919,0.767 1.058,0.937 0.139,0.170 10 A 0.524,0.918 0.662,1.088 0.139,0.170 10 A 2.909,1.068 3.047,1.238 0.139,0.170 10 A 3.012,1.569 3.150,1.739 0.139,0.170 10 A 1.389,2.706 1.528,2.876 0.139,0.170 10 A 1.018,2.442 1.156,2.612 0.139,0.170 10 A 0.832,2.235 0.970,2.405 0.139,0.170 10 A 0.623,2.067 0.761,2.237 0.139,0.170 10 A 0.142,1.907 0.281,2.076 0.139,0.170 10 A 2.976,1.927 3.229,2.096 0.253,0.170 10 B 2.71,2.704 2.963,2.874 0.253,0.170 10 B 2.311,2.775 2.564,2.944 0.253,0.170 10 B

Install the differential cross shaft bearing retainer and front differential front support assembly LH with the 14 bolts.

Torque:
for bolt A : 65 N*m (663 kgf*cm, 48 ft.*lbf)
for bolt B : 155 N*m (1581 kgf*cm, 114 ft.*lbf)


e.

Hold the companion flange firmly and rotate it in both directions.


f.

Remove the 14 bolts, differential case, shaft bearing retainer and front support.


g.

Inspect the tooth contact pattern.

C116070E06
1.583,1.906 1.833,2.104 0.25,0.198 10 false *a 2.875,0.594 3.104,0.75 0.229,0.156 10 false *b 2.771,3.448 3,3.615 0.229,0.167 10 false *e 4.969,0.552 5.177,0.729 0.208,0.177 10 false *c 5.073,3.427 5.271,3.604 0.198,0.177 10 false *f 3.688,4.677 3.958,4.917 0.271,0.24 10 false *g 3.677,2.073 3.917,2.25 0.24,0.177 10 false *d

Text in Illustration
*a Proper Contact *b Heel Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear (*b, *c)
*e Toe Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear (*e, *f) - -

If the teeth are not engaged properly, use the following chart to select the appropriate washer for correction.

Standard Washer Thickness:
Specified Condition Specified Condition
1.815 to 1.835 mm (0.0715 to 0.0722 in.) 2.065 to 2.085 mm (0.0813 to 0.0820 in.)
1.840 to 1.860 mm (0.0725 to 0.0732 in.) 2.090 to 2.110 mm (0.0823 to 0.0830 in.)
1.865 to 1.885 mm (0.0735 to 0.0742 in.) 2.115 to 2.135 mm (0.0833 to 0.0840 in.)
1.890 to 1.910 mm (0.0744 to 0.0752 in.) 2.140 to 2.160 mm (0.0843 to 0.0850 in.)
1.915 to 1.935 mm (0.0754 to 0.0762 in.) 2.165 to 2.185 mm (0.0853 to 0.0860 in.)
1.940 to 1.960 mm (0.0764 to 0.0772 in.) 2.190 to 2.210 mm (0.0863 to 0.0870 in.)
1.965 to 1.985 mm (0.0774 to 0.0781 in.) 2.215 to 2.235 mm (0.0872 to 0.0879 in.)
1.990 to 2.010 mm (0.0784 to 0.0791 in.) 2.240 to 2.260 mm (0.0882 to 0.0889 in.)
2.015 to 2.035 mm (0.0794 to 0.0801 in.) 2.265 to 2.285 mm (0.0892 to 0.0899 in.)
2.040 to 2.060 mm (0.0804 to 0.0811 in.) -



Hide 41204D 24.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 41214C 25.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41141L 26.REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

Hide 41301L 27.REMOVE NO. 1 FRONT DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 41211B 29.REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING

Hide 41231F 30.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

a.

Install a new bearing spacer.


Hide 31.TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION

Hide 41301L 32.INSTALL NO. 1 FRONT DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 41141L 33.INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

a.

Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential carrier and shaft bearing retainer.


b.

Wipe off any residual FIPG material on the contact surface using gasoline or alcohol.


c.
C214104E04
1.063,0.25 1.438,0.25 false 1.438,0.25 1.781,0.604 false 0.927,1.521 1.052,1.677 0.125,0.156 10 false A 0.854,0.146 1.042,0.323 0.188,0.177 10 false *a

Apply seal packing to the differential carrier as shown in the illustration.

Text in Illustration
*a Seal Packing

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Seal Diameter (A):

2.0 to 3.0 mm (0.0788 to 0.118 in.)


HINT:

Install the shaft bearing retainer within 10 minutes of applying seal packing.



d.
C160133E01
2.303,0.58 2.441,0.750 0.139,0.170 10 A 1.4,0.626 1.539,0.795 0.139,0.170 10 A 0.919,0.767 1.058,0.937 0.139,0.170 10 A 0.524,0.918 0.662,1.088 0.139,0.170 10 A 2.909,1.068 3.047,1.238 0.139,0.170 10 A 3.012,1.569 3.150,1.739 0.139,0.170 10 A 1.389,2.706 1.528,2.876 0.139,0.170 10 A 1.018,2.442 1.156,2.612 0.139,0.170 10 A 0.832,2.235 0.970,2.405 0.139,0.170 10 A 0.623,2.067 0.761,2.237 0.139,0.170 10 A 0.142,1.907 0.281,2.076 0.139,0.170 10 A 2.976,1.927 3.229,2.096 0.253,0.170 10 B 2.71,2.704 2.963,2.874 0.253,0.170 10 B 2.311,2.775 2.564,2.944 0.253,0.170 10 B

Install the front differential cross shaft bearing retainer and front differential front support assembly LH with the 11 bolts (A) and 3 new bolts (B).

Torque:
for bolt A : 65 N*m (663 kgf*cm, 48 ft.*lbf)
for bolt B : 155 N*m (1581 kgf*cm, 114 ft.*lbf)

NOTICE:

Do not add oil or drive the vehicle immediately after installing the cover, and leave it as is for at least an hour. Also, for 12 hours or less, avoid rapid acceleration/deceleration.



Hide 41211B 34.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING

a.
C159432E02
2.198,1.044 2.521,1.331 2.521,1.331 2.704,1.331 false 2.765,1.237 3.139,1.428 0.375,0.191 10 SST

Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

SST
09316-60011  (09316-00041)


Hide 41214C 35.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41101D 36.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL

a.
C159273E02
1.964,1.266 2.224,1.353 2.224,1.353 2.367,1.353 false 2.39,1.266 2.845,1.472 0.455,0.206 10 SST

Using SST and a hammer, tap in a new oil seal.

SST
09502-12010  
09316-60011  (09316-00041)

Standard oil seal depth:

5.6 to 6.6 mm (0.221 to 0.259 in.)



b.

Coat the lip of the oil seal with MP grease.


Hide 41204D 37.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C358635E03
1,0.323 1.188,0.323 1.188,0.323 1.49,0.625 false 0.667,0.26 1.125,0.458 0.458,0.198 10 false SST 0.594,1.531 1.052,1.729 0.458,0.198 10 false *b 2.698,0.76 3.156,0.958 0.458,0.198 10 false *a

Using SST, install the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

Text in Illustration
*a Turn
*b Hold


Hide 38.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.

Coat the threads of a new nut with hypoid gear oil.


b.
C159272E02
0.338,0.534 0.653,0.676 0.316,0.142 10 SST 0.717,0.618 0.876,0.618 0.876,0.618 1.152,0.747 false

Using SST to hold the companion flange in place, then slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).

SST
09330-00021  (09330-00030)

Limit Torque Value:

451 N*m (4599 kgf*cm, 332ft.*lbf) or less



c.
C358623

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard Preload (at Starting):
Bearing Specified Condition
New 2.97 to 3.47 N*m (31 to 35 kgf*cm, 27 to 30 in.*lbf)
Reused 2.14 to 2.45 N*m (22 to 24 kgf*cm, 19 to 21 in.*lbf)


If the preload is more than the specification, replace the bearing spacer.

If the preload is less than the specification, tighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.

Torque:
451 N*m (4599 kgf*cm, 333 ft.*lbf)

or less


If the maximum torque is exceeded while tightening the nut, replace the bearing spacer and repeat the preload procedure.

HINT:

Do not loosen the nut to reduce the preload.



Hide 39.INSPECT TOTAL PRELOAD

a.
C358623

With the drive pinion contacting the tooth side of the ring gear, use a torque wrench to measure the total preload.

Standard Total Preload (at Starting):
Bearing Specified Condition
New 4.58 to 5.88 N*m (47 to 59 kgf*cm, 41 to 52 in.*lbf)
Reused 3.47 to 4.58 N*m (36 to 46 kgf*cm, 31 to 40 in.*lbf)



Hide 40.INSPECT BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION

a.
C159798E03
1.615,1.125 1.073,0.854 1.073,0.854 0.844,0.854 true 0.49,0.771 0.948,0.979 0.458,0.208 10 false SST

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-33010  

Standard backlash:

0.17 to 0.27 mm (0.00670 to 0.0106 in.)



Hide 41204D 41.INSPECT RUNOUT OF FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C160138E03
0.709,0.309 0.928,0.508 0.220,0.199 10 *a 2.525,0.309 2.744,0.508 0.220,0.199 10 *b 2.571,2.601 2.790,2.800 0.220,0.199 10 *c

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


Text in Illustration
*a Vertical Runout
*b Lateral Runout
*c 55 mm (2.17 in.)

If the runout is more than the maximum, replace the companion flange.


Hide 41204E 42.STAKE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT

a.
C160139

Using a chisel and hammer, stake the nut.


Hide 41304P 43.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
C177464E02
2.135,1.063 2.646,1.479 2.646,1.479 2.76,1.479 true 2.802,1.385 3.104,1.573 0.302,0.188 10 false SST

Using SST and a plastic-faced hammer, tap in a new oil seal until its surface is flush with the differential carrier end.

SST
09608-32010  


b.

Coat the lip of the oil seal with MP grease.

Standard oil seal depth:

-0.45 to 0.45 mm (-0.0177 to 0.0177 in.)



Hide 41321 44.INSTALL DIFFERENTIAL EXTENSION FLANGE TUBE

a.

Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential tube and bearing retainer.


b.

Wipe off any residual FIPG material on the contact surface using gasoline or alcohol.


c.
C176060E05
1.667,1.292 1.167,1.792 1.167,1.792 1.063,1.792 true 1.146,0.469 1.281,0.667 0.135,0.198 10 false A 0.906,1.698 1.281,1.865 0.375,0.167 10 false *a

Apply seal packing to the bearing retainer as shown in the illustration.

Text in Illustration
*a Seal Packing

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Seal Diameter (A):

2.0 to 3.0 mm (0.0788 to 0.118 in.)


HINT:

Install the differential tube within 10 minutes of applying seal packing.



d.

Install the differential tube to the bearing retainer.


e.
C171952

Install 4 new bolts.

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)

or less


NOTICE:

Do not add oil or drive the vehicle immediately after installing the cover, and leave it as is for at least an hour. Also, for 12 hours or less, avoid rapid acceleration/deceleration.