Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL › 2014.08–2015.08
RM2660E _52 Drivetrain _052812 AXLE AND DIFFERENTIAL _0255358 REAR DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 41204G 3.REMOVE DRIVE PINION COMPANION FLANGE REAR NUT

a.
C089309E17
1.333,0.51 1.583,0.188 1.583,0.188 1.698,0.188 false 1.729,0.104 2.063,0.26 0.333,0.156 10 false SST

Using SST and a hammer, loosen the staked part of the nut.

SST
09930-00010  


b.
B087842E17
2.781,0.99 2.625,0.99 2.625,0.99 2.375,1.188 false 2.844,0.896 3.167,1.052 0.323,0.156 10 false SST

Using SST to hold the companion flange, remove the nut.

SST
09330-00021  (09330-00030)


Hide 41204 4.REMOVE REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
C311665E01
1.523,0.787 1.523,0.244 1.523,0.244 1.202,0.244 false 0.826,0.172 1.144,0.337 0.318,0.165 10 SST

Using SST, remove the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


Hide 41201C 5.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C311666E01
1.399,0.85 1.399,0.333 1.399,0.333 1.713,0.333 false 1.752,0.251 2.060,0.407 0.309,0.156 10 SST

Using SST, remove the oil seal.

SST
09308-10010  


Hide 41214 6.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 7.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C311667E01
1.434,0.686 1.434,0.376 1.434,0.376 0.987,0.376 false 0.637,0.301 0.946,0.457 0.309,0.156 10 SST

Using SST, remove the front bearing (inner race) from the drive pinion.

SST
09556-22010  


b.
C161826E02
1.558,1.075 1.188,0.667 1.188,0.667 1.005,0.667 false 0.637,0.58 0.949,0.739 0.312,0.159 10 SST

Using SST, remove the front bearing (outer race) from the drive pinion.

SST
09308-00010  


Hide 41231 8.REPLACE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C311457

Replace the bearing spacer with a new one.


Hide 41201B 9.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C311668E01
1.971,1.645 2.290,1.807 0.319,0.163 10 SST 2.133,1.285 2.133,1.627 false

Using SST and a hammer, tap in the bearing (outer race).

SST
09316-60011  (09316-00011, 09316-00021)


b.

Install the bearing (inner race).


Hide 41214 10.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201C 11.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C311669E01
1.896,1.427 1.896,1.698 1.896,1.698 1.542,1.698 false 1.229,1.615 1.563,1.781 0.333,0.167 10 false SST

Using SST and a hammer, tap in a new oil seal.

SST
09214-76011  

Standard oil seal depth:

0.05 to 0.95 mm (0.00197 to 0.0374 in.)



b.

Coat the lip of the oil seal with MP grease.


Hide 41204 12.INSTALL REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
C311670E01
1.488,0.787 1.488,0.318 1.488,0.318 1.093,0.318 false 0.72,0.232 1.048,0.407 0.327,0.174 10 SST

Using SST, install the companion flange to the drive pinion.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


Hide 13.ADJUST DRIVE PINION PRELOAD

a.

Coat the threads of a new nut with hypoid gear oil.


b.
C088916E09
2.729,0.813 2.604,0.813 2.604,0.813 2.354,1.01 false 2.76,0.719 3.052,0.896 0.292,0.177 10 false SST

Using SST to hold the companion flange in place, then slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).

SST
09330-00021  (09330-00030)

Limit Torque Value:

441 N*m (4497 kgf*cm, 325 ft.*lbf) or less



c.
C124126

Using a torque wrench, measure the preload.

Standard Preload (at Starting):
Bearing Specified Condition
New 1.04 to 1.69 N*m (11 to 17 kgf*cm, 10 to 14 in.*lbf)
Reused 0.85 to 1.37 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)


If the preload is not within the specification, adjust the preload.


Hide 41204G 17.STAKE DRIVE PINION COMPANION FLANGE REAR NUT

a.
C089310

Using a chisel and hammer, stake the nut.