Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for Standard) › 2015.08–2017.08
RM2660E _52 Drivetrain _052812 AXLE AND DIFFERENTIAL _0255359 REAR DIFFERENTIAL CARRIER ASSEMBLY(for Standard) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for Standard)  REASSEMBLY  


PROCEDURE

Hide 1.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

a.
C124142

Install the 2 thrust washers to the side gears.


b.

Install the side gears to the differential case.


c.

Install the 4 pinion gears and 4 thrust washers to the spider.


d.

Install the spider assembly to the differential case.

HINT:

Install the spider to the differential case tightly.



e.
C161846

Using a dial indicator, measure the side gear backlash while holding the side gear and spider.

Standard backlash:

0.02 to 0.15 mm (0.000788 to 0.00590 in.)


HINT:
·

Measure at all 4 pinion gear locations.

·

Measure the backlash at the differential case LH and RH.

·

Apply hypoid gear oil to each sliding surface and rotating part.


If the backlash is not within the specification, replace the side gear thrust washers with washers of a different thickness.


Standard Washer Thickness:
Part No. Specified Condition Part No. Specified Condition
41361-60560 1.53 to 1.57 mm (0.0603 to 0.0618 in.) 41361-60620 1.83 to 1.87 mm (0.0721 to 0.0736 in.)
41361-60570 1.58 to 1.62 mm (0.0622 to 0.0637 in.) 41361-60630 1.88 to 1.92 mm (0.0741 to 0.0755 in.)
41361-60580 1.63 to 1.67 mm (0.0642 to 0.0657 in.) 41361-60640 1.93 to 1.97 mm (0.0760 to 0.0775 in.)
41361-60590 1.68 to 1.72 mm (0.0662 to 0.0677 in.) 41361-60650 1.98 to 2.02 mm (0.0780 to 0.0795 in.)
41361-60600 1.73 to 1.77 mm (0.0682 to 0.0696 in.) 41361-60660 2.03 to 2.07 mm (0.0800 to 0.0814 in.)
41361-60610 1.78 to 1.82 mm (0.0701 to 0.0716 in.) 41361-60670 2.08 to 2.12 mm (0.0819 to 0.0834 in.)



Hide 2.ASSEMBLE DIFFERENTIAL CASE

a.

Install the spider assembly to the differential case.

HINT:

Install the spider to the differential case tightly.



b.
C161843E12
1.885,1.333 2.375,1 2.375,1 2.542,1 true 2.594,0.906 2.99,1.094 0.396,0.188 10 false *a

Align the matchmarks and assemble the differential case LH and RH.

Text in Illustration
*a Matchmark


c.

Install the 8 bolts and tighten them uniformly, a little at a time.

Torque:
47 N*m (480 kgf*cm, 35 ft.*lbf)


Hide 41301A 3.INSTALL REAR DIFFERENTIAL CASE BEARING

a.
C161847E02
0.934,0.397 1.182,0.723 false 1.266,0.508 1.182,0.393 1.182,0.393 0.813,0.393 false 0.42,0.316 0.741,0.464 0.321,0.148 10 SST

Using SST and a press, press the RH side bearing (inner race) into the differential case.

SST
09710-30050  
09950-70010  (09951-07150)


b.
C161848E04
1,0.625 0.854,0.396 0.854,0.396 0.417,0.396 false 0.719,0.406 0.938,0.844 true 0.5,0.396 0.948,1.5 true 0.115,0.323 0.438,0.479 0.323,0.156 10 false SST

Using SST and a press, press the LH side bearing (inner race) into the differential case.

SST
09710-30050  
09950-60010  (09951-00480)
09950-70010  (09951-07150)


Hide 4.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the threads of the bolts and differential case with non-residue solvent.


b.

Clean the contact surfaces of the differential case and ring gear.


c.

Heat the ring gear to about 100°C (212°F) in boiling water.


d.

Carefully take the ring gear out of the boiling water.


e.

After the moisture on the ring gear has completely evaporated, quickly align the matchmarks on the ring gear and differential case and set the ring gear onto the differential case. Then temporarily install the 12 bolts so that the bolt holes in the ring gear and differential case are aligned.


f.
C161840E07
1.229,1.458 1.76,1.135 1.76,1.135 2.177,1.135 true 2.229,1.042 2.427,1.208 0.198,0.167 10 false *a

After the ring gear cools down sufficiently, remove the 12 bolts. Then apply thread lock adhesive to the 12 bolts and install them.

Text in Illustration
*a Matchmark

Thread lock:

Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent


Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


Hide 5.CHECK DIFFERENTIAL RING GEAR RUNOUT

a.

Install the differential case assembly to the differential carrier, and then install the adjust nut so that the case bearing does not rattle.

NOTICE:

Make sure to install the case bearings (outer races) and adjust nuts to the correct side (LH or RH).



b.

Install the 2 bearing caps with the 4 bearing cap bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


c.
C161850

Using a dial indicator, check the ring runout.

Maximum runout:

0.05 mm (0.00197)


If the runout is more than the maximum, replace the ring gear.


d.

Remove the differential case.

NOTICE:

Separate the case bearings (outer races) and adjust nuts for the LH and RH sides.



Hide 41201B 6.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C161851E04
1.656,0.74 1.385,0.427 1.385,0.427 0.896,0.427 false 1.063,0.427 1.552,1.083 true 0.594,0.333 0.938,0.531 0.344,0.198 10 false SST

Using SST and a press, press in the bearing (outer race).

SST
09950-60020  (09951-00710)
09950-70010  (09951-07150)


Hide 41201A 7.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C162726E04
1.729,0.792 1.458,0.458 1.458,0.458 0.979,0.458 false 1.125,0.458 1.635,1.156 true 0.646,0.396 1.021,0.573 0.375,0.177 10 false SST

Using SST and a press, press in the bearing (outer race).

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


Hide 41201A 8.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.

Install the washer to the drive pinion.

HINT:

After installing the washer, check the tooth contact pattern. If necessary, replace the washer with one of a different thickness.



b.
C161852E07
1.49,1.021 1.135,0.75 1.135,0.75 0.896,0.75 false 1.865,1.333 2.24,1.094 2.24,1.094 2.406,1.094 false 0.698,0.667 1.094,0.865 0.396,0.198 10 false *1 2.458,1 2.948,1.188 0.49,0.188 10 false SST

Using SST and a press, press the rear bearing (inner race) into the drive pinion.

SST
09506-35010  

Text in Illustration
*1 Plate Washer


Hide 9.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C028218

Install the drive pinion, front bearing (inner race) and oil slinger.

HINT:

Install the spacer and oil seal after adjusting the gear contact pattern.



b.
C161853E05
1.438,0.635 1.135,0.417 1.135,0.417 0.896,0.417 false 0.51,0.333 0.885,0.5 0.375,0.167 10 false SST 2.802,0.688 3.01,0.885 0.208,0.198 10 false *a 0.469,1.51 0.677,1.708 0.208,0.198 10 false *b

Using SST, install the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

Text in Illustration
*a Turn
*b Hold


c.
C161854E02
0.18,0.663 0.518,0.826 0.338,0.162 10 SST 0.922,0.843 0.668,0.745 0.668,0.745 0.553,0.745 false

Using SST to hold the companion flange in place, then slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).

SST
09330-00021  (09330-00030)

Limit Torque Value:

441 N*m (4497 kgf*cm, 325 ft.*lbf) or less


NOTICE:
·

Apply hypoid gear oil to the nut.

·

As there is no spacer, tighten a little at a time, being careful not to overtighten it.




d.
C124126

Using a torque wrench, measure the preload.

Standard Preload (at Starting):
Reduction Ratio Bearing Specified Condition
3.307 New 1.32 to 2.22 N*m (14 to 22 kgf*cm, 12 to 19 in.*lbf)
Reused 0.52 to 0.87 N*m (6 to 8 kgf*cm, 5 to 7 in.*lbf)
3.909
4.100
4.300
New 0.73 to 1.38 N*m (8 to 14 kgf*cm, 7 to 12 in.*lbf)
Reused 0.54 to 1.06 N*m (6 to 10 kgf*cm, 5 to 9 in.*lbf)


HINT:

Measure the total preload after turning the bearing clockwise and counterclockwise several times to make the bearing smooth.



Hide 10.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.

Place the bearing (outer races) on their respective bearings.

HINT:

Do not interchange the left and right outer races.



b.

Install the differential case to the carrier.

HINT:

Make sure that there is backlash between the ring gear and drive pinion.



Hide 41315 11.INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT

a.
C161855

Install the 2 adjusting nuts to the carrier, making sure the nuts are threaded properly.


Hide 12.INSPECT AND ADJUST DIFFERENTIAL RING GEAR BACKLASH

a.
C161856E08
1.125,1.469 1,1.833 1,1.833 0.823,1.833 true 0.615,1.75 0.875,1.969 0.26,0.219 10 false *a

Align the matchmarks on the bearing caps and carrier. Screw in the 4 bearing cap bolts 2 or 3 turns and press down the bearing caps by hand.

Text in Illustration
*a Matchmark

HINT:

If the bearing caps do not fit tightly on the carrier, the adjusting nuts are not engaged properly.


Reinstall the adjusting nuts if necessary.


b.
C161857

Tighten the 4 bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


c.
C161858E04
0.646,0.5 0.885,0.5 0.885,0.5 1.583,1.177 true 0.281,0.417 0.594,0.583 0.313,0.167 10 false SST

Loosen the 4 bolts to the point where the adjusting nuts can be turned by SST.

SST
09504-00011  


d.

Using SST, tighten the adjusting nut on the ring gear side until the ring gear has a backlash of about 0.2 mm (0.00787 in.).

SST
09504-00011  


e.
C161859E03
1.906,1.438 2.563,0.74 2.563,0.74 2.771,0.74 true 2.823,0.656 3.146,0.802 0.323,0.146 10 false SST

While turning the ring gear, use SST to tighten the adjusting nut on the drive pinion side. After the bearings are settled, loosen the adjusting nut on the drive pinion side.


f.
C161860E02
2.891,0.804 3.221,0.967 0.330,0.163 10 SST 2.558,1.048 2.72,0.892 2.72,0.892 2.849,0.892 false

Place a dial indicator on the top of the adjusting nut on the ring gear side.


g.

Adjust the side bearing to zero preload by tightening the other adjusting nut until the pointer on the indicator begins to move.


h.
C161859E03
1.906,1.438 2.563,0.74 2.563,0.74 2.771,0.74 true 2.823,0.656 3.146,0.802 0.323,0.146 10 false SST

Using SST, tighten the adjusting nut 1 to 1.5 notches from the zero preload position.

SST
09504-00011  


i.
C161861E05
2.01,1.313 2.542,1.031 2.542,1.031 2.75,1.031 true 2.833,0.969 3.135,1.135 0.302,0.167 10 false SST

Using a dial indicator, adjust the ring gear backlash until it is within the specification.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


HINT:

The backlash is adjusted by turning the left and right adjusting nuts by an equal amount. For example, loosen the nut on the left side 1 notch and tighten the nut on the right side 1 notch.



j.
C161857

Tighten the 4 bearing cap bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


k.

After rotating the ring gear 5 turns or more, recheck the ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)



Hide 13.INSPECT TOTAL PRELOAD

a.
C124126

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Drive Pinion Preload (at Starting):
Reduction Ratio Bearing Specified Condition
3.307 New 1.77 to 2.95 N*m (19 to 30 kgf*cm, 16 to 26 in.*lbf)
Reused 0.97 to 1.60 N*m (10 to 16 kgf*cm, 9 to 14 in.*lbf)
3.909
4.100
4.300
New 1.11 to 2.01 N*m (12 to 20 kgf*cm, 10 to 17 in.*lbf)
Reused 0.92 to 1.69 N*m (10 to 17 kgf*cm, 9 to 14 in.*lbf)



Hide 14.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.
C161862

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


b.

Turn the companion flange in both directions and inspect the ring gear for proper tooth contact.

C247128E02
0.172,0.993 0.390,1.190 0.218,0.198 10 *a 2.602,0.047 2.821,0.244 0.218,0.198 10 *b 4.863,0.052 5.081,0.249 0.218,0.198 10 *c 3.714,1.443 3.932,1.640 0.218,0.198 10 *d 2.635,1.845 2.854,2.042 0.218,0.198 10 *e 4.975,1.882 5.193,2.080 0.218,0.198 10 *f 3.742,3.25 3.960,3.448 0.218,0.198 10 *g

Text in Illustration
*a Proper Contact *b Heel Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear (*b, *c)
*e Toe Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear (*e, *f) - -

If the teeth are not contacting properly, use the following table and select a proper washer for correction.

Standard Washer Thickness:
Part No. Specified Condition Part No. Specified Condition
90564-40004 1.04 to 1.06 mm (0.0410 to 0.0417 in.) 90564-40016 1.315 to 1.335 mm (0.0518 to 0.0525 in.)
90564-40006 1.065 to 1.085 mm (0.0420 to 0.0427 in.) 90564-40017 1.34 to 1.36 mm (0.0528 to 0.0535 in.)
90564-40007 1.09 to 1.11 mm (0.0430 to 0.0437 in.) 90564-40018 1.365 to 1.385 mm (0.0538 to 0.0545 in.)
90564-40008 1.115 to 1.135 mm (0.0439 to 0.0446 in.) 90564-40019 1.39 to 1.41 mm (0.0548 to 0.0555 in.)
90564-40009 1.14 to 1.16 mm (0.0449 to 0.0456 in.) 90564-40020 1.415 to 1.435 mm (0.0557 to 0.0564 in.)
90564-40010 1.165 to 1.185 mm (0.0459 to 0.0466 in.) 90564-40021 1.44 to 1.46 mm (0.0567 to 0.0574 in.)
90564-40011 1.19 to 1.21 mm (0.0469 to 0.0476 in.) 90564-40022 1.465 to 1.485 mm (0.0577 to 0.0584 in.)
90564-40012 1.215 to 1.235 mm (0.0479 to 0.0486 in.) 90564-40023 1.49 to 1.51 mm (0.0587 to 0.0594 in.)
90564-40013 1.24 to 1.26 mm (0.0489 to 0.0496 in.) 90564-40024 1.515 to 1.535 mm (0.0597 to 0.0604 in.)
90564-40014 1.265 to 1.285 mm (0.0498 to 0.0505 in.) 90564-40025 1.54 to 1.56 mm (0.0607 to 0.0614 in.)
90564-40015 1.29 to 1.31 mm (0.0508 to 0.0515 in.) - -



Hide 41204G 15.REMOVE DRIVE PINION COMPANION FLANGE REAR NUT

a.
C161836E02
2.275,0.629 2.5,0.47 2.5,0.47 2.645,0.472 false 2.686,0.382 3.023,0.540 0.336,0.158 10 SST

Using SST to hold the flange, remove the nut.

SST
09330-00021  (09330-00030)


Hide 41204 16.REMOVE REAR DRIVE PINION REAR COMPANION FLANGE SUB-ASSEMBLY

Hide 41214 17.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 18.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 41231 19.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.

Install a new spacer to the drive pinion.


Hide 41201B 20.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C311668E01
1.971,1.645 2.290,1.807 0.319,0.163 10 SST 2.133,1.285 2.133,1.627 false

Using SST and a hammer, tap in the bearing (outer race).

SST
09316-60011  (09316-00011, 09316-00021)


b.

Install the bearing (inner race).


Hide 41214 21.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201C 22.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

Hide 41204 23.INSTALL REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
C161853E05
1.438,0.635 1.135,0.417 1.135,0.417 0.896,0.417 false 0.51,0.333 0.885,0.5 0.375,0.167 10 false SST 2.802,0.688 3.01,0.885 0.208,0.198 10 false *a 0.469,1.51 0.677,1.708 0.208,0.198 10 false *b

Using SST, install the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

Text in Illustration
*a Turn
*b Hold


b.

Coat the threads of a new nut with hypoid gear oil.


c.
Z101162E01
0.469,0.844 0.594,0.844 0.594,0.844 0.708,1.104 false 0.208,0.76 0.667,0.958 0.458,0.198 10 false SST

Using SST to hold the companion flange in place, then slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).

SST
09330-00021  (09330-00030)

Limit Torque Value:

441 N*m (4497 kgf*cm, 325 ft.*lbf) or less



d.
C124126

Using a torque wrench, measure the preload.

Standard Drive Pinion Preload (at Starting):
Reduction Ratio Bearing Specified Condition
3.307 New 1.67 to 2.57 N*m (18 to 26 kgf*cm, 15 to 22 in.*lbf)
Reused 0.87 to 1.22 N*m (9 to 12 kgf*cm, 8 to 10 in.*lbf)
3.909
4.100
4.300
New 1.08 to 1.73 N*m (12 to 17 kgf*cm, 10 to 15 in.*lbf)
Reused 0.89 to 1.41 N*m (10 to 14 kgf*cm, 8 to 12 in.*lbf)



Hide 24.INSPECT TOTAL PRELOAD

a.
C124126

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Drive Pinion Preload (at Starting):
Reduction Ratio Bearing Specified Condition
3.307 New 2.12 to 3.30 N*m (22 to 33 kgf*cm, 19 to 29 in.*lbf)
Reused 1.32 to 1.95 N*m (14 to 19 kgf*cm, 12 to 17 in.*lbf)
3.909
4.100
4.300
New 1.46 to 2.36 N*m (15 to 24 kgf*cm, 13 to 20 in.*lbf)
Reused 1.27 to 2.04 N*m (13 to 20 kgf*cm, 12 to 18 in.*lbf)



Hide 25.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C161835

Using a dial indicator, measure the ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


HINT:

Measure at 3 or more positions around the circumference of the ring gear.


If the backlash is not as specified, adjust the side bearing preload or repair as necessary.


Hide 41204 26.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
F001237E41
0.552,0.167 0.76,0.333 0.208,0.167 10 false *a 2.229,0.156 2.417,0.302 0.188,0.146 10 false *b 2.25,1.823 2.594,1.99 0.344,0.167 10 false *c

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


Text in Illustration
*a Vertical Runout
*b Lateral Runout
*c 35 mm (1.38 in.)

If the runout is more than the maximum, replace the companion flange.


Hide 41204G 27.STAKE DRIVE PINION COMPANION FLANGE REAR NUT

a.
C161318

Using a chisel and hammer, stake the nut.


Hide 41316 28.INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C161866

Install 2 new nut locks to the bearing caps.


b.

Install the 2 bolts, and bend the nut locks.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)