Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL › from 2015.08
RM2660E _52 Drivetrain _052812 AXLE AND DIFFERENTIAL _0255358 REAR DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 41204G 3.REMOVE DRIVE PINION COMPANION FLANGE REAR NUT

a.
C236628E02
1.121,0.525 1.374,0.195 1.374,0.195 1.799,0.195 false 1.846,0.113 2.169,0.280 0.323,0.166 10 SST

Using SST and a hammer, loosen the staked part of the nut.

SST
09930-00010  


b.
C236629E01
2.715,1.129 3.034,1.299 0.318,0.170 10 SST 2.247,1.205 2.682,1.205 false 0.509,0.363 0.674,0.521 0.165,0.158 10 *a 2.187,1.738 2.352,1.896 0.165,0.158 10 *b

Using SST to hold the companion flange, remove the nut.

SST
09330-00021  (09330-00030)

Text in Illustration
*a Turn
*b Hold


Hide 41204 4.REMOVE REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
C344316E01
1.198,0.344 1.479,0.344 1.479,0.344 1.479,0.781 false 0.875,0.271 1.333,0.469 0.458,0.198 10 false SST

Using SST, remove the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


Hide 41201C 5.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C344317E01
1.417,0.861 1.417,0.346 1.417,0.346 1.623,0.346 false 1.67,0.26 2.000,0.416 0.330,0.156 10 SST

Using SST, remove the oil seal.

SST
09308-10010  


Hide 41214 6.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 7.REMOVE REAR DRIVE PINION FRONT BEARING

a.
C311667E01
1.434,0.686 1.434,0.376 1.434,0.376 0.987,0.376 false 0.637,0.301 0.946,0.457 0.309,0.156 10 SST

Using SST, remove the front bearing (inner race) from the drive pinion.

SST
09556-22010  


b.
C161826E02
1.558,1.075 1.188,0.667 1.188,0.667 1.005,0.667 false 0.637,0.58 0.949,0.739 0.312,0.159 10 SST

Using SST, remove the front bearing (outer race) from the drive pinion.

SST
09308-00010  


Hide 41231 8.REPLACE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C311457

Replace the bearing spacer with a new one.


Hide 41201B 9.INSTALL REAR DRIVE PINION FRONT BEARING

a.
C311668E01
1.971,1.645 2.290,1.807 0.319,0.163 10 SST 2.133,1.285 2.133,1.627 false

Using SST and a hammer, tap in the bearing (outer race).

SST
09316-60011  (09316-00011, 09316-00021)


b.

Install the bearing (inner race).


Hide 41214 10.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201C 11.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C344318E02
1.885,1.427 1.885,1.719 1.885,1.719 1.583,1.719 false 1.24,1.635 1.552,1.792 0.313,0.156 10 false SST

Using SST and a hammer, tap in a new oil seal.

SST
09214-76011  

Standard oil seal depth:

1.55 to 2.45 mm (0.0611 to 0.0964 in.)



b.

Coat the lip of the oil seal with MP grease.


Hide 41204 12.INSTALL REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
C344319E01
1.494,0.793 1.494,0.305 1.494,0.305 1.059,0.305 false 0.692,0.224 1.014,0.384 0.323,0.161 10 SST

Using SST, install the companion flange to the drive pinion.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


b.

Coat the threads of a new nut with hypoid gear oil.


c.
C344320E01
2.376,1.064 2.116,1.291 2.116,1.291 1.952,1.291 false 1.588,1.211 1.909,1.371 0.320,0.161 10 SST

Using SST to hold the companion flange in place, then slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).

Limit Torque Value:

441 N*m (4497 kgf*cm, 325 ft.*lbf) or less



Hide 41204G 16.STAKE DRIVE PINION COMPANION FLANGE REAR NUT

a.
C089310

Using a chisel and hammer, stake the nut.