Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1718  Pressure Sensor Circuit Malfunction  


DESCRIPTION

This circuit is used for sending the data to detect the pressure output from the pump. The abnormality of the fluid pressure is judged by the ECU.

DTC Code Detecting Condition Trouble Area
C1718 When one of the following conditions is met:
·

When detecting an abnormal signal from the pressure sensor (pressure sensor terminal voltage of ECU is 0.3 V or less or 4.6 V or more) for 1 second.

·

When there is a pressure sensor power supply voltage malfunction.

·

When the pump motor is not operating and a pressure of 1 MPa (10.2 kgf/cm2, 145 psi) or more is placed on the pressure sensor for 20 seconds or more.


·

Harness or connector

·

Height control pump and motor (Pressure sensor)

·

Suspension control ECU



WIRING DIAGRAM

C176909E04
5.729,0.698 6.208,0.844 0.479,0.146 10 false SPB 5.708,1.563 6.188,1.708 0.479,0.146 10 false SPG 5.708,2.396 6.188,2.542 0.479,0.146 10 false PACC 5.313,0.563 5.521,0.771 0.208,0.208 10 false 10 5.302,1.385 5.521,1.594 0.219,0.208 10 false 19 5.333,2.292 5.531,2.552 0.198,0.26 10 false 20 5.146,3.042 6.74,3.302 1.594,0.26 10 false Suspension Control ECU 5.146,2.865 5.469,3.042 0.323,0.177 10 false K35 0.677,3.031 1.781,3.271 1.104,0.24 10 false Pressure Sensor 0.677,2.833 0.875,3.031 0.198,0.198 10 false i2 1.25,1.552 1.604,1.729 0.354,0.177 10 false SHG 1.24,0.656 1.594,0.823 0.354,0.167 10 false SHB 1.177,2.417 1.615,2.604 0.438,0.188 10 false PACC 1.76,2.25 1.906,2.469 0.146,0.219 10 false 2 1.76,0.542 1.885,0.729 0.125,0.188 10 false 1 1.771,1.448 1.896,1.656 0.125,0.208 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - SUSPENSION CONTROL ECU)
NOTICE:

When inspecting the wire harness between the suspension control ECU and pressure sensor, it is difficult to determine the malfunctioning area if there is a sensor power supply malfunction. Therefore, disconnect the connectors for the pressure sensor, the acceleration sensors (front RH, front LH) and fluid temperature sensor on the ECU side.


a.

Disconnect the i2 pressure sensor connector.


b.

Disconnect the K34 and K35 ECU connectors.

U164777E02
5.052,1.635 4.302,1.635 true 5.354,1.646 6.052,1.646 true 5.229,1.844 5.24,2.385 true 1.646,1.917 0.635,2.01 0.635,2.01 0.635,2.125 true 1.646,1.979 1.479,2.271 1.479,2.271 1.479,2.354 true 1.698,1.979 2.01,2.25 true 0.625,0.073 2.938,0.479 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.083,0.073 6.49,0.594 2.406,0.521 10 false Front view of wire harness connector: (to Pressure Sensor) 0.333,2.208 0.969,2.375 0.635,0.167 10 false 10 (SPB) 2.042,2.271 2.771,2.5 0.729,0.229 10 false 19 (SPG) 1.188,2.385 1.927,2.552 0.74,0.167 10 false 20 (PACC) 3.958,1.563 4.292,1.76 0.333,0.198 10 false SHB 6.104,1.563 6.542,1.719 0.438,0.156 10 false PACC 5.125,2.406 5.521,2.604 0.396,0.198 10 false SHG 1.042,1.708 1.354,1.917 0.313,0.208 10 false K35 2.198,1.719 2.49,1.938 0.292,0.219 10 false K34 4.51,1.208 4.781,1.396 0.271,0.188 10 false i2


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K35-10 (SPB) - i2-1 (SHB) Always Below 1 Ω
K35-19 (SPG) - i2-3 (SHG) Always Below 1 Ω
K35-20 (PACC) - i2-2 (PACC) Always Below 1 Ω
K35-10 (SPB) - Body ground Always 10 kΩ or higher
K35-19 (SPG) - Body ground Always 10 kΩ or higher
K35-20 (PACC) - Body ground Always 10 kΩ or higher




OK

2.CHECK SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK SUSPENSION CONTROL ECU
a.

Connect the K34 and K35 suspension control ECU connectors.


b.

Disconnect the i2 pressure sensor connector.


U164778E02
1.927,2.521 2.729,2.708 2.729,2.708 2.729,2.771 true 1.667,2.292 0.813,2.615 0.813,2.615 0.813,2.688 true 0.323,0.167 2.729,0.688 2.406,0.521 10 false Front view of wire harness connector: (to Pressure Sensor) 0.625,2.719 1.104,2.917 0.479,0.198 10 false SHB 2.583,2.823 2.979,3.021 0.396,0.198 10 false SHG 1.771,1.438 1.938,1.604 0.167,0.167 10 false i2

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
i2-1 (SHB) - i2-3 (SHG) Engine switch on (IG) 4.75 to 5.25 V




OK

3.CHECK PRESSURE SENSOR

NG

REPLACE SUSPENSION CONTROL ECU

3.CHECK PRESSURE SENSOR
a.

Connect the K34 and K35 suspension control ECU connectors.


b.

Connect the i2 pressure sensor connector.


c.
U164779E02
1.813,2.042 1.177,2.458 1.177,2.458 1.177,2.635 true 1.875,2.052 2.49,2.521 2.49,2.521 2.49,2.667 true 0.344,0.083 2.656,0.49 2.313,0.406 10 false Component with harness connected: (Suspension Control ECU) 0.76,2.677 1.469,2.865 0.708,0.188 10 false 20 (PACC) 2.177,2.698 2.813,2.885 0.635,0.188 10 false 19 (SPG) 1.635,2.479 1.906,2.667 0.271,0.188 10 false K35

Start the engine and push the up button of the height control switch to activate height control.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K35-20 (PACC) - K35-19 (SPG) While height control is operating. 1.48 to 2.54 V




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPLACE HEIGHT CONTROL PUMP AND MOTOR