| DTC Code | Detection Condition | Trouble Area |
|---|---|---|
| C1782 | While the engine switch is on (IG), voltage at terminal IG, BAT and/or BAT2 is 10 V or less, or 16 V or more for 0.5 seconds. | ·
Battery ·
Charging system ·
Harness or connector ·
AHC-B fuse ·
AHC-B No. 2 fuse ·
Suspension control ECU |
Even if DTC C1781 is stored at the same time, perform the inspection for DTC C1782 first.
Before performing troubleshooting, inspect the connectors of related circuits.
If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and the GTS on.
Read the "IG Power Source Voltage" item in the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| IG Power Source Voltage | Power supply voltage /
min.: 0 V max.: 255 V |
Engine switch on (IG): 11 to 14 V | - |
11 to 14 V
OK
NG
Clear the DTCs (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>DTC CHECK / CLEAR).
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and the GTS on.
Read the "+B Power Source Voltage" and "+B2 Power Source Voltage" items in the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| +B Power Source Voltage | Power supply for absorber control actuator /
min.: 0 V max.: 255 V |
Engine switch on (IG): 11 to 14 V | - |
| +B2 Power Source Voltage | Power supply for No. 1 height control valve and front suspension control valve /
min.: 0 V max.: 255 V |
Engine switch on (IG): 11 to 14 V | - |
11 to 14 V
OK
NG
Remove the AHC-B and AHC-B No. 2 fuses from the cowl side junction block RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AHC-B fuse | Always | Below 1 Ω |
| AHC-B No. 2 fuse | Always | Below 1 Ω |
OK
NG
Disconnect the K34 and K35 ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K34-3 (BAT2) - Body ground | Engine switch on (IG) | 11 to 14 V |
| K35-1 (BAT) - Body ground | Engine switch on (IG) | 11 to 14 V |
OK
NG
Disconnect the K34 ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K34-5 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (1UR-FE) | B |
| NG (1VD-FTV) | C |
| NG (3UR-FE) | D |
A
B
C
D