Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1791  Absorber Control Switch Circuit (Test Mode DTC)  


DESCRIPTION

This circuit is used for sending the signal to the suspension control ECU to switch to the damping mode selected by the damping force control switch.

DTC Code Detection Condition Trouble Area
C1791 The test mode procedure is performed.
·

Harness or connector

·

Suspension control switch (Damping forcer control switch)

·

Suspension control ECU



WIRING DIAGRAM

C177058E07
1.903,1.825 3.819,2.057 1.916,0.232 10 Damping Force Control Switch 5.464,0.347 5.611,0.562 0.147,0.215 10 2 5.751,1.217 6.341,1.418 0.590,0.201 10 TSW2 5.445,1.119 5.566,1.313 0.121,0.194 10 9 5.238,1.911 6.885,2.169 1.647,0.258 10 Suspension Control ECU 2.888,0.454 3.308,0.629 0.420,0.174 10 ECU1 2.891,1.215 3.311,1.390 0.420,0.174 10 ECU2 1.903,1.649 2.096,1.817 0.193,0.168 10 V4 3.49,0.352 3.624,0.534 0.134,0.182 10 6 3.503,1.123 3.651,1.315 0.148,0.192 10 5 1.71,0.776 1.914,0.951 0.203,0.175 10 16 5.751,0.463 6.268,0.671 0.517,0.207 10 TSW1 5.238,1.734 5.533,1.913 0.295,0.179 10 K34 2.075,0.879 2.254,1.044 0.180,0.165 10 E

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SPORT SWITCH, COMFORT SWITCH)
a.

Turn the engine switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG) and the tester on.


d.

Enter the following menus: Chassis / AHC / Data List.


e.

According to the display on the tester, read the Data List.

AHC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPORT Switch Damping force control switch (SPORT) /
ON or OFF
ON: SPORT
OFF: NORMAL or COMFORT
-
COMFORT Switch Damping force control switch (COMFORT) /
ON or OFF
ON: COMFORT
OFF: NORMAL or SPORT
-


OK:

On the tester screen, item changes between ON and OFF according to switch operation.



OK

2.TEST MODE INSPECTION

NG

3.INSPECT SUSPENSION CONTROL SWITCH (DAMPING FORCE CONTROL SWITCH)
2.TEST MODE INSPECTION
a.

Refer to the Test Mode Procedure and perform the signal check. Check that test mode DTC C1791 is cleared (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>TEST MODE PROCEDURE).

Result
Result Proceed to
DTC C1791 is not cleared A
DTC C1791 is cleared B



A

REPLACE SUSPENSION CONTROL ECU

B

3.INSPECT SUSPENSION CONTROL SWITCH (DAMPING FORCE CONTROL SWITCH)
a.

Remove the suspension control switch (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>REMOVAL).


b.
C261415E06
1.635,2.021 0.979,2.542 0.979,2.542 0.979,2.698 true 1.719,2.24 1.854,2.552 1.854,2.552 1.854,2.708 true 1.854,2.01 2.469,2.531 2.469,2.531 2.469,2.688 true 0.094,0.073 2.656,0.438 2.563,0.365 10 false Component without harness connected: (Suspension Control Switch) 0.74,2.708 1.177,2.885 0.438,0.177 10 false ECU1 2.24,2.708 2.677,2.885 0.438,0.177 10 false ECU2 1.813,2.729 1.948,2.896 0.135,0.167 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (ECU2) - 16 (E) COMF Below 1 Ω
Except COMF 10 kΩ or higher
6 (ECU1) - 16 (E) SPORT Below 1 Ω
Except SPORT 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - SWITCH AND BODY GROUND)

NG

REPLACE SUSPENSION CONTROL SWITCH

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - SWITCH AND BODY GROUND)
U164849E02
2.365,1.896 2.667,1.594 2.667,1.594 2.76,1.594 false 2.375,1.979 2.667,2.219 2.667,2.219 2.75,2.219 false 5.25,1.948 5.125,2.188 5.125,2.188 5.125,2.292 true 5.125,1.771 4.406,2.198 4.406,2.198 4.406,2.302 true 5.271,1.76 5.865,2.198 5.865,2.198 5.865,2.302 true 0.625,0.115 2.938,0.521 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.083,0.115 6.49,0.49 2.406,0.375 10 false Front view of wire harness connector: (to Suspension Control Switch) 1.594,1.719 1.875,1.906 0.281,0.188 10 false K34 2.813,1.521 3.458,1.698 0.646,0.177 10 false 2 (TSW1) 2.813,2.135 3.531,2.333 0.719,0.198 10 false 9 (TSW2) 5.083,2.344 5.208,2.531 0.125,0.188 10 false E 5.677,2.354 6.094,2.563 0.417,0.208 10 false ECU1 4.198,2.313 4.677,2.5 0.479,0.188 10 false ECU2 5.104,1.021 5.302,1.177 0.198,0.156 10 false V4

a.

Disconnect the K34 ECU connector.


b.

Disconnect the V4 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K34-2 (TSW1) - V4-6 (ECU1) Always Below 1 Ω
K34-2 (TSW1) - Body ground Always 10 kΩ or higher
K34-9 (TSW2) - V4-5 (ECU2) Always Below 1 Ω
K34-9 (TSW2) - Body ground Always 10 kΩ or higher
V4-16 (E) - Body ground Always Below 1 Ω




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR