Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1792  Height Control Switch Circuit (Test Mode DTC)  


DESCRIPTION

This circuit sends a signal to the suspension control ECU in order to adjust the height to the selected height by the height control switch.

DTC Code Detection Condition Trouble Area
C1792 The test mode procedure is performed.
·

Harness or connector

·

Suspension control switch (Height control switch)

·

Suspension control ECU



WIRING DIAGRAM

C177058E16
1.917,1.833 3.698,2.25 1.781,0.417 10 false Height Control Switch 5.427,0.396 5.604,0.615 0.177,0.219 10 false 20 5.76,1.313 6.354,1.51 0.594,0.198 10 false DNSW 5.417,1.177 5.615,1.375 0.198,0.198 10 false 21 5.292,1.875 6.938,2.135 1.646,0.26 10 false Suspension Control ECU 3.073,1.333 3.313,1.51 0.24,0.177 10 false LO 3.104,0.573 3.292,0.75 0.188,0.177 10 false HI 2.083,0.979 2.635,1.208 0.552,0.229 10 false E 3.5,0.417 3.771,0.656 0.271,0.24 10 false 7 3.49,1.167 3.615,1.354 0.125,0.188 10 false 8 1.729,0.833 1.927,1.021 0.198,0.188 10 false 16 5.76,0.552 6.281,0.76 0.521,0.208 10 false UPSW 5.292,1.74 5.594,1.896 0.302,0.156 10 false K34 1.917,1.677 2.146,1.885 0.229,0.208 10 false V4

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (HEIGHT CONTROL SWITCH (UP), HEIGHT CONTROL SWITCH (DOWN))
a.

Turn the engine switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG) and the tester on.


d.

Enter the following menus: Chassis / AHC / Data List.


e.

According to the display on the tester, read the Data List.

AHC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Control Switch(Up) Height control switch (Up) /
ON or OFF
ON: Up button of the height control switch is pushed.
OFF: Height control switch is not pushed.
-
Height Control Switch(Down) Height control switch (Down) /
ON or OFF
ON: Down button of the height control switch is pushed.
OFF: Height control switch is not pushed.
-


OK:

On the tester screen, item changes between ON and OFF according to switch operation.



OK

2.TEST MODE INSPECTION

NG

3.INSPECT SUSPENSION CONTROL SWITCH (HEIGHT CONTROL SWITCH)
2.TEST MODE INSPECTION
a.

Refer to the Test Mode Procedure and perform the signal check. Check that test mode DTC C1792 is cleared (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>TEST MODE PROCEDURE).

Result
Result Proceed to
DTC C1792 is not cleared A
DTC C1792 is cleared B



A

REPLACE SUSPENSION CONTROL ECU

B

3.INSPECT SUSPENSION CONTROL SWITCH (HEIGHT CONTROL SWITCH)
a.

Remove the suspension control switch (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>REMOVAL).


b.
C261415E07
1.365,2.031 0.927,2.552 0.927,2.552 0.927,2.708 true 1.719,2.24 1.854,2.552 1.854,2.552 1.854,2.708 true 1.583,2.021 2.573,2.542 2.573,2.542 2.573,2.698 true 0.094,0.083 2.656,0.448 2.563,0.365 10 false Component without harness connected: (Suspension Control Switch) 2.5,2.719 2.688,2.896 0.188,0.177 10 false HI 0.854,2.708 1.083,2.885 0.229,0.177 10 false LO 1.813,2.75 1.948,2.917 0.135,0.167 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (LO) - 16 (E) Down button of the height control switch is pushed. Below 1 Ω
Height control switch is not pushed or the up button is pushed. 10 kΩ or higher
7 (HI) - 16 (E) Up button of the height control switch is pushed. Below 1 Ω
Height control switch is not pushed or the down button is pushed. 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - SWITCH AND BODY GROUND)

NG

REPLACE SUSPENSION CONTROL SWITCH

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - SWITCH AND BODY GROUND)
U164850E02
2.375,2.042 2.833,2.333 2.833,2.333 2.833,2.396 false 2.323,2.031 1.698,2.302 1.698,2.302 1.698,2.385 false 5.25,1.948 5.083,2.177 5.083,2.177 5.083,2.313 true 5.354,1.771 5.49,2.177 5.49,2.177 5.49,2.313 true 5.469,1.781 5.927,2.188 5.927,2.188 5.927,2.323 true 0.625,0.073 2.938,0.479 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.083,0.073 6.49,0.448 2.406,0.375 10 false Front view of wire harness connector: (to Suspension Control Switch) 1.583,1.719 1.885,1.906 0.302,0.188 10 false K34 2.521,2.406 3.281,2.583 0.76,0.177 10 false 20 (UPSW) 1.385,2.406 2.26,2.604 0.875,0.198 10 false 21 (DNSW) 5.052,2.344 5.167,2.531 0.115,0.188 10 false E 5.844,2.354 6.083,2.563 0.24,0.208 10 false LO 5.438,2.354 5.625,2.542 0.188,0.188 10 false HI 5.104,1.021 5.406,1.229 0.302,0.208 10 false V4

a.

Disconnect the K34 ECU connector.


b.

Disconnect the V4 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K34-20 (UPSW) - V4-7 (HI) Always Below 1 Ω
K34-20 (UPSW) - Body ground Always 10 kΩ or higher
K34-21 (DNSW) - V4-8 (LO) Always Below 1 Ω
K34-21 (DNSW) - Body ground Always 10 kΩ or higher
V4-16 (E) - Body ground Always Below 1 Ω




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR