Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › from 2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1792  Height Control Switch Circuit (Test Mode DTC)  


DESCRIPTION

This circuit sends a signal to the suspension control ECU in order to adjust the height to the selected height by the height control switch (integration control and panel assembly).

DTC Code Detection Condition Trouble Area
C1792 The test mode procedure is performed.
·

Harness or connector

·

Height control switch (integration control and panel assembly)

·

Suspension control ECU



WIRING DIAGRAM

C177058E17
1.917,1.885 4.229,2.302 2.313,0.417 10 false Height Control Switch (Integration Control and Panel Assembly) 5.427,0.438 5.604,0.656 0.177,0.219 10 false 20 5.76,1.302 6.354,1.5 0.594,0.198 10 false DNSW 5.417,1.177 5.615,1.375 0.198,0.198 10 false 21 5.292,1.969 6.938,2.229 1.646,0.26 10 false Suspension Control ECU 3.073,1.333 3.313,1.51 0.24,0.177 10 false LO 3.104,0.563 3.292,0.74 0.188,0.177 10 false HI 2.083,0.99 2.635,1.219 0.552,0.229 10 false E 3.5,0.448 3.771,0.688 0.271,0.24 10 false 8 3.49,1.198 3.615,1.385 0.125,0.188 10 false 4 1.729,0.875 1.927,1.063 0.198,0.188 10 false 10 5.76,0.563 6.281,0.771 0.521,0.208 10 false UPSW 5.292,1.781 5.594,1.938 0.302,0.156 10 false K34 1.917,1.677 2.146,1.885 0.229,0.208 10 false V8

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.READ VALUE USING GTS (HEIGHT CONTROL SWITCH (UP), HEIGHT CONTROL SWITCH (DOWN))
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and the GTS on.


d.

Enter the following menus: Chassis / AHC / Data List.


e.

According to the display on the GTS, read the Data List.

AHC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Control Switch(Up) Height control switch (Up) /
ON or OFF
ON: Up button of the height control switch pushed.
OFF: Height control switch not pushed.
-
Height Control Switch(Down) Height control switch (Down) /
ON or OFF
ON: Down button of the height control switch pushed.
OFF: Height control switch not pushed.
-


OK:

The GTS displays ON or OFF according to height control switch (integration control and panel assembly) operation.



OK

2.TEST MODE INSPECTION

NG

3.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY
2.TEST MODE INSPECTION
a.

Refer to the Test Mode Procedure and perform the signal check. Check that test mode DTC C1792 is cleared (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>TEST MODE PROCEDURE).

Result
Result Proceed to
DTC C1792 is not cleared A
DTC C1792 is cleared B



A

REPLACE SUSPENSION CONTROL ECU

B

3.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY
a.

Remove the height control switch (integration control and panel assembly) (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>REMOVAL).


b.

Inspect the height control switch (integration control and panel assembly) (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - INTEGRATION CONTROL AND PANEL ASSEMBLY AND BODY GROUND)

NG

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - INTEGRATION CONTROL AND PANEL ASSEMBLY AND BODY GROUND)
a.

Disconnect the K34 suspension control ECU connector.


b.

Disconnect the V8 height control switch (integration control and panel assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K34-20 (UPSW) - V8-8 (HI) Always Below 1 Ω
K34-20 (UPSW) or V8-8 (HI) - Body ground Always 10 kΩ or higher
K34-21 (DNSW) - V8-4 (LO) Always Below 1 Ω
K34-21 (DNSW) or V8-4 (LO) - Body ground Always 10 kΩ or higher
V8-10 (E) - Body ground Always Below 1 Ω




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR