Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1794  Height Control OFF Switch Circuit (Test Mode DTC)  


DESCRIPTION

This is the height control system main switch. When the height control switch is pushed, the height control OFF indicator light lights up and height control turns off.

The off condition of the height control will not be canceled until the height control switch is pushed again or the vehicle is driven.

DTC Code Detection Condition Trouble Area
C1794 The test mode procedure is performed.
·

Harness or connector

·

Suspension control switch (Height control OFF switch)

·

Suspension control ECU



WIRING DIAGRAM

C177227E08
1.826,1.359 3.645,1.773 1.819,0.414 10 Height Control OFF Switch 5.684,0.596 5.963,0.797 0.279,0.201 10 TD 5.36,0.487 5.627,0.774 0.267,0.287 10 11 5.239,1.734 6.886,1.991 1.647,0.258 10 Suspension Control ECU 2.017,0.594 2.404,0.767 0.387,0.172 10 E 3.125,0.616 3.332,0.781 0.207,0.165 10 N 5.239,1.582 5.571,1.764 0.332,0.182 10 K34 1.826,1.205 2.027,1.354 0.201,0.149 10 V4 1.676,0.49 1.876,0.660 0.200,0.170 10 16 3.42,0.476 3.534,0.639 0.114,0.163 10 9

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.INSPECT SUSPENSION CONTROL SWITCH (HEIGHT CONTROL OFF SWITCH)
a.

Remove the suspension control switch (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>REMOVAL).


b.
C261415E03
0.095,0.079 2.658,0.447 2.564,0.367 10 Component without harness connected: (Suspension Control Switch) 0.91,2.686 1.063,2.862 0.153,0.176 10 N 1.242,1.996 0.966,2.515 0.966,2.515 0.966,2.67 false 1.74,2.204 1.871,2.518 1.871,2.518 1.871,2.67 false 1.812,2.686 1.945,2.855 0.132,0.169 10 E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (N) - 16 (E) Height control OFF switch is pushed. Below 1 Ω
Height control OFF switch is not pushed. 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - SWITCH AND BODY GROUND)

NG

REPLACE SUSPENSION CONTROL SWITCH

2.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - SWITCH AND BODY GROUND)
U164851E02
2.302,1.979 2.646,1.615 2.646,1.615 2.76,1.615 false 5.24,1.938 5.01,2.167 5.01,2.167 5.01,2.281 true 5.583,1.771 5.958,2.177 5.958,2.177 5.958,2.292 true 0.625,0.063 2.938,0.469 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.083,0.063 6.49,0.438 2.406,0.375 10 false Front view of wire harness connector: (to Suspension Control Switch) 1.594,1.719 1.865,1.906 0.271,0.188 10 false K34 2.813,1.542 3.458,1.719 0.646,0.177 10 false 11 (TD) 4.99,2.281 5.115,2.469 0.125,0.188 10 false E 5.927,2.333 6.094,2.542 0.167,0.208 10 false N 5.104,1.021 5.385,1.229 0.281,0.208 10 false V4

a.

Disconnect the K34 ECU connector.


b.

Disconnect the V4 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K34-11 (TD) - V4-9 (N) Always Below 1 Ω
K34-11 (TD) - Body ground Always 10 kΩ or higher
V4-16 (E) - Body ground Always Below 1 Ω




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR