Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.08–2016.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This is the power source for the tire pressure warning ECU and receiver.

WIRING DIAGRAM

C281617E07
5.219,2.479 6.719,2.698 1.5,0.219 10 false L65*1, L75*2 5.219,2.667 6.688,3.052 1.469,0.385 10 false Tire Pressure Warning ECU and Receiver 5.417,0.771 5.635,1.031 0.219,0.26 10 false IG 5.417,1.854 5.792,2.063 0.375,0.208 10 false GND 5.198,0.677 5.344,0.927 0.146,0.25 10 false 1 5.135,1.771 5.323,1.99 0.188,0.219 10 false 12 3.51,0.958 4.729,1.208 1.219,0.25 10 false ECU-IG NO. 2 1.302,0.802 2.458,1.042 1.156,0.24 10 false from IG Circuit 0.292,3.042 3.052,3.417 2.76,0.375 10 false *1: w/o Front Antenna 0.292,3.365 3.229,3.698 2.938,0.333 10 false *2: w/ Front Antenna

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECU - BATTERY AND BODY GROUND)
a.
U165206E02
1.208,1.219 0.906,1.823 true 2.177,1.469 2.49,1.917 true 0.167,0.021 0.375,0.208 0.208,0.188 10 false *a 0.25,0.76 0.542,0.917 0.292,0.156 10 false L65 0.667,0.781 0.917,0.938 0.25,0.156 10 false *A 0.25,1.125 0.542,1.281 0.292,0.156 10 false L75 0.667,1.146 0.958,1.302 0.292,0.156 10 false *B 0.781,1.854 1.031,2.042 0.25,0.188 10 false IG 2.427,1.917 2.823,2.104 0.396,0.188 10 false GND

Disconnect the L65*1 or L75*2 tire pressure warning ECU and receiver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L65-1 (IG) - Body ground*1
L75-1 (IG) - Body ground*2
Engine switch on (IG) 10 to 16 V
Engine switch off Below 1 V


*1: w/o Front Antenna

*2: w/ Front Antenna



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-12 (GND) - Body ground*1
L75-12 (GND) - Body ground*2
Always Below 1 Ω


*1: w/o Front Antenna

*2: w/ Front Antenna


Text in Illustration
*A w/o Front Antenna
*B w/ Front Antenna
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR