Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2014.08–2015.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM D

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  INITIALIZATION  


NOTICE:
·

Initialization can be confirmed through the tire pressure warning light.

·

The order in which the data is received is random.

·

If the signals from all the wheels are received, initialization is completed.

·

Initialization is completed when the Data List "ID Tire Inflation Pressure" display shows the correct pressures (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST).

·

Initialization is normally completed within a few minutes.

·

It may take up to a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25 (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121/21).

·

If initialization has not been completed successfully, DTC C2177/77 is stored after the vehicle is driven at a speed of 37 km/h (23 mph) or more for 10 minutes or more.

·

During test mode (sensor check mode), the system will not change to initialization mode even if the tire pressure warning reset switch is pushed.

·

While the answer-back function for the ID switching function is operating, the system will not change to initialization mode even if the tire pressure warning reset switch is pressed.

·
C217594E29
1.781,1.469 2.031,1.802 true 1.563,0.917 1.458,0.49 1.458,0.49 1.344,0.49 true 0.156,0.083 0.833,0.365 0.677,0.281 10 false *a 2.052,1.844 2.313,2.031 0.26,0.188 10 false TC 1.083,0.417 1.438,0.594 0.354,0.177 10 false CG

Initialization can be terminated by connecting terminals 13 (TC) and 4 (CG) of the DLC3.



Text in Illustration
*a Front view of DLC3

BEFORE INITIALIZATION


a.

Make sure that the tires are cold.


b.

Set the air pressure of all tires to the specified value(s) (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).



INITIALIZATION PROCEDURE


a.

Turn the engine switch on (IG).


b.

Press and hold the tire pressure warning reset switch for 3 seconds or more so that the tire pressure warning light blinks 3 times.

C309675E02
0.125,0.083 0.344,0.271 0.219,0.188 10 false *1 1.573,0.073 1.875,0.333 0.302,0.26 10 false *A 2.823,0.969 3.073,1.198 0.25,0.229 10 false *2 0.427,1.708 0.677,1.906 0.25,0.198 10 false *a 0.49,2.021 0.719,2.229 0.229,0.208 10 false *c 0.49,2.24 0.729,2.448 0.24,0.208 10 false *d 1.271,1.656 1.51,1.896 0.24,0.24 10 false *b 1.073,2.521 1.313,2.771 0.24,0.25 10 false *b 3.208,0.125 3.458,0.344 0.25,0.219 10 false *1 4.604,0.115 4.854,0.333 0.25,0.219 10 false *B 4.167,1.677 4.385,1.917 0.219,0.24 10 false *a 4.271,2.021 4.479,2.229 0.208,0.208 10 false *c 4.271,2.24 4.5,2.448 0.229,0.208 10 false *d 5.063,1.677 5.302,1.896 0.24,0.219 10 false *b 4.875,2.583 5.115,2.792 0.24,0.208 10 false *b 6.583,0.938 6.792,1.135 0.208,0.198 10 false *2

Text in Illustration
*A for RHD *B for LHD
*1 Tire Pressure Warning Light *2 Tire Pressure Warning Reset Switch
*a Tire Pressure Warning Light Output Pattern *b 1 sec.
*c ON *d OFF


c.

Turn the engine switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Check that initialization has been completed.


h.

Confirm that the tire pressure data of all tires is displayed on the GTS screen.