Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2014.08–2015.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light comes on and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. DTC Detection Condition Trouble Area
C2198/98 Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C249283E33
2.177,1.531 4.635,1.771 2.458,0.24 10 false Tire Pressure Warning Reset Switch 5.156,2.969 6.885,3.458 1.729,0.49 10 false Tire Pressure Warning ECU and Receiver 5.177,2.802 5.479,3 0.302,0.198 10 false L60 2.302,0.917 2.49,1.115 0.188,0.198 10 false 2 2.49,0.917 2.698,1.125 0.208,0.208 10 false E 3.115,0.917 3.396,1.135 0.281,0.219 10 false INT 3.417,0.917 3.625,1.125 0.208,0.208 10 false 1 5.229,0.906 5.438,1.115 0.208,0.208 10 false 2 5.469,1.021 5.823,1.24 0.354,0.219 10 false CS1 2.198,1.375 2.688,1.594 0.49,0.219 10 false E116

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.

Remove the tire pressure warning reset switch (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>REMOVAL).


b.

Inspect the tire pressure warning reset switch (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the tire pressure warning reset switch E116 connector.


b.

Disconnect the tire pressure warning ECU and receiver L60 connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-2 (CS1) - E116-1 (INT) Always Below 1 Ω
L60-2 (CS1) or E116-1 (INT) - Body ground Always 10 kΩ or higher
E116-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR