Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

If any of the following is detected, the ABS warning light remains on.

·

The skid control ECU (master cylinder solenoid) connectors are disconnected from the skid control ECU (master cylinder solenoid).

·

There is a malfunction in the skid control ECU (master cylinder solenoid) internal circuit.

·

There is an open in the harness between the combination meter assembly and skid control ECU (master cylinder solenoid).


HINT:

There is a case that the GTS cannot be used when the skid control ECU (master cylinder solenoid) is abnormal.


WIRING DIAGRAM

C257366E09
5.354,0.854 5.917,1.146 0.563,0.292 10 false A24 5.417,0.667 5.792,0.896 0.375,0.229 10 false 46 5.729,0.823 6.229,1.104 0.5,0.281 10 false IG1 5.729,1.313 6.323,1.573 0.594,0.26 10 false GND1 5.729,1.802 6.323,2.042 0.594,0.24 10 false GND2 5.74,2.26 6.25,2.552 0.51,0.292 10 false GND3 5.354,1.323 5.833,1.604 0.479,0.281 10 false A24 5.365,1.802 5.833,2.063 0.469,0.26 10 false A24 5.365,2.271 5.875,2.563 0.51,0.292 10 false A25 5.396,1.625 5.844,1.885 0.448,0.26 10 false 32 5.438,1.146 5.771,1.365 0.333,0.219 10 false 1 5.438,2.094 5.719,2.292 0.281,0.198 10 false 4 0.385,2.448 0.729,2.635 0.344,0.188 10 false E119 0.385,2.625 2.521,2.948 2.135,0.323 10 false Combination Meter Assembly 1.063,3.219 3.135,3.448 2.073,0.229 10 false : CAN Communication System 5.281,2.917 6.958,3.365 1.677,0.448 10 false Skid Control ECU (Master Cylinder Solenoid) 3.531,0.854 4.625,1.281 1.094,0.427 10 false from IG Circuit

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check the skid control ECU (master cylinder solenoid) connector connection.

OK:

The connector is securely connected.




OK

2.INSPECT BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1VD-FTV) C
NG (for 1UR-FE) D
NG (for 3UR-FE) E



A

3.CHECK CAN COMMUNICATION LINE

B

C

D

E

3.CHECK CAN COMMUNICATION LINE
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and the GTS on.


d.

Select "CAN Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

OK:

"CAN Bus Check" indicates no malfunctions in CAN communication.


Result
Result Proceed to
OK A
NG (for LHD (with Central Gateway ECU)) B
NG (for LHD (without Central Gateway ECU)) C
NG (for RHD (with Central Gateway ECU)) D
NG (for RHD (without Central Gateway ECU)) E



A

4.CHECK DTC (CAN COMMUNICATION SYSTEM)

B

C

D

E

4.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and the GTS on.





g.

for RHD (without Central Gateway ECU):

Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD (with Central Gateway ECU)) B
CAN DTC is output (for LHD (without Central Gateway ECU)) C
CAN DTC is output (for RHD (with Central Gateway ECU)) D
CAN DTC is output (for RHD (without Central Gateway ECU)) E



A

5.PERFORM ACTIVE TEST USING GTS (INDICAT. LAMP ABS)

B

C

D

E

5.PERFORM ACTIVE TEST USING GTS (INDICAT. LAMP ABS)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the condition of the ABS warning light by operating the GTS.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Lamp ABS ABS Warning Light ON or OFF Perform the test with the vehicle stopped and engine idling.

OK:

The warning light turns on or off when operating the GTS.




OK

6.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

6.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

OK

7.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)
a.

Turn the ignition switch off.


b.
U156048E03
0.635,1.438 0.448,2.208 false 0.99,1.688 1.229,2.167 false 1.865,4.021 2.302,4.021 false 0.135,0.125 0.375,0.333 0.24,0.208 10 false *a 0.25,2.24 0.656,2.469 0.406,0.229 10 false GND1 1.094,2.219 1.5,2.448 0.406,0.229 10 false GND2 2.385,3.938 2.833,4.115 0.448,0.177 10 false GND3 0.125,0.927 0.458,1.125 0.333,0.198 10 false A24 0.771,3.75 1.094,3.917 0.323,0.167 10 false A25

Disconnect the skid control ECU (master cylinder solenoid) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-1 (GND1) - Body ground Always Below 1 Ω
A24-32 (GND2) - Body ground Always Below 1 Ω
A25-4 (GND3) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C