Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2017.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

The signal check circuit detects trouble in the sensor or switch signal which cannot be detected by the DTC check.

Connecting terminals TS and CG of the DLC3 starts the check.

WIRING DIAGRAM

C173350E26
0.917,0.875 1.188,1.052 0.271,0.177 10 false TS 0.906,1.76 1.208,1.99 0.302,0.229 10 false CG 5.458,3.052 7.125,3.5 1.667,0.448 10 false Skid Control ECU (Master Cylinder Solenoid) 0.458,2.938 0.917,3.156 0.458,0.219 10 false E22 0.458,3.125 0.938,3.354 0.479,0.229 10 false DLC3 1.271,1.615 1.521,1.792 0.25,0.177 10 false 4 1.25,0.74 1.625,0.917 0.375,0.177 10 false 12 6.052,0.875 6.323,1.052 0.271,0.177 10 false TS 5.469,2.875 5.854,3.063 0.385,0.188 10 false A24 5.719,0.76 5.938,0.938 0.219,0.177 10 false 24

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DLC3 (TS))
a.

Turn the ignition switch off.


b.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-24 (TS) - E22-12 (TS) Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (DLC3 (CG) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DLC3 (CG) - BODY GROUND)
a.
U156267E02
1.781,0.198 1.635,0.198 1.635,0.198 1.635,0.823 true 0.115,0.083 0.323,0.313 0.208,0.229 10 false *1 0.146,1.333 0.438,1.51 0.292,0.177 10 false E22 1.833,0.115 2.125,0.323 0.292,0.208 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*1 DLC3



OK

3.CHECK HARNESS AND CONNECTOR (DLC3 (TS) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 (TS) - BODY GROUND)
a.
U156268E02
1.604,1.479 1.604,1.927 1.604,1.927 1.875,1.927 true 0.083,0.094 0.292,0.323 0.208,0.229 10 false *1 0.135,1.344 0.427,1.521 0.292,0.177 10 false E22 1.938,1.844 2.271,2.052 0.333,0.208 10 false TS

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-12 (TS) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 DLC3

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C