Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1407
C1408 |
Either condition is met:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Rear speed sensor RH/LH ·
Skid control sensor wire ·
Speed sensor circuit ·
Skid control ECU (Master cylinder solenoid) |
DTC C1407 is for the rear speed sensor RH.
DTC C1408 is for the rear speed sensor LH.
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Speed Open | Rear speed sensor RH open circuit detection/ Error or Normal | Normal | - |
| RL Speed Open | Rear speed sensor LH open circuit detection/ Error or Normal | Normal | - |
Normal (there are no momentary interruptions).
Perform the above inspection before removing the sensor and connector.
OK
NG
OK
NG
Clear the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output (for LHD) | B |
| DTC is output (for RHD) | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
| *A | for RH | *B | for LH |
| *1 | Skid Control Sensor Wire | - | - |
Remove the skid control sensor wire (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Nz1-4 - z19-2 (RR+) | Always | Below 1 Ω |
| Nz1-3 - z19-1 (RR-) | Always | Below 1 Ω |
| Nz1-4 - Nz1-3 | Always | 10 kΩ or higher |
| Nz1-4 - Nz1-1 | Always | 10 kΩ or higher |
| Nz1-4 - Nz1-2 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Nz1-2 - z20-2 (RL+) | Always | Below 1 Ω |
| Nz1-1 - z20-1 (RL-) | Always | Below 1 Ω |
| Nz1-2 - Nz1-1 | Always | 10 kΩ or higher |
| Nz1-2 - Nz1-3 | Always | 10 kΩ or higher |
| Nz1-2 - Nz1-4 | Always | 10 kΩ or higher |
OK
NG
Install the skid control sensor wire (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSTALLATION).
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Disconnect the z19 and/or z20 speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-5 (RR+) - z19-2 (RR+) | Always | Below 1 Ω |
| A24-5 (RR+) - Body ground | Always | 10 kΩ or higher |
| A24-19 (RR-) - z19-1 (RR-) | Always | Below 1 Ω |
| A24-19 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-20 (RL+) - z20-2 (RL+) | Always | Below 1 Ω |
| A24-20 (RL+) - Body ground | Always | 10 kΩ or higher |
| A24-6 (RL-) - z20-1 (RL-) | Always | Below 1 Ω |
| A24-6 (RL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the skid control ECU (master cylinder solenoid) connector.
Disconnect the speed sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z19-2 (RR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z20-2 (RL+) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Rear Speed Sensor) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C