The skid control ECU (master cylinder solenoid) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.
The yaw rate and acceleration sensor has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0124 (acceleration sensor communication trouble) are stored.
The DTCs are also stored when the calibration has not been completed.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1210 | Zero point calibration of the yaw rate sensor is incomplete. | ·
Zero point calibration incomplete ·
Sensor installation ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
Skid control ECU (Master cylinder solenoid) |
| C1336 | Zero point calibration of the acceleration sensor is incomplete. |
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
After replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
for LHD (with Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
for LHD (without Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
for RHD (with Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
for RHD (without Central Gateway ECU):
Check for DTCs (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
| Result | Proceed to |
|---|---|
| CAN DTC is not output | A |
| CAN DTC is output (for LHD (with Central Gateway ECU)) | B |
| CAN DTC is output (for LHD (without Central Gateway ECU)) | C |
| CAN DTC is output (for RHD (with Central Gateway ECU)) | D |
| CAN DTC is output (for RHD (without Central Gateway ECU)) | E |
A
B
C
D
E
Perform zero point calibration of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
NEXT
Turn the ignition switch off.
Perform the signal check in the Test Mode Procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
All test mode DTCs are cleared.
OK
NG
Turn the ignition switch off.
Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).
The sensor is tightened to the specified torque.
The sensor is not installed at an angle.
OK
NG
(See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION)
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Deceleration Sensor | Acceleration sensor reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | Changes continuously during acceleration/deceleration. |
| Deceleration Sensor2 | Acceleration sensor 2 reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | Changes continuously during acceleration/deceleration. |
| Yaw Rate Sensor | Yaw rate sensor/ Min.: -128°/s, Max.: 127°/s | Vehicle stationary: 0°/s
Right turn: -128 to 0°/s Left turn: 0 to 127°/s |
- |
Check that the yaw rate and acceleration sensor output value is displayed on the GTS.
The yaw rate and acceleration sensor output value is normal.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C