Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU (master cylinder solenoid), the relay contact turns on and the stop light comes on.

DTC Code DTC Detection Condition Trouble Area
C1380 Either condition is met:
1.

When the voltage at the IG1 terminal is between 11 and 14 V and the stop light control relay drive output (STPO) is on, a signal is not input to the STP2 terminal for 5 seconds or more.

2.

When the voltage at the IG1 terminal is between 11 and 14 V and the stop light control relay drive output (STPO) is off, the signal at the STP terminal is different from the input signal at the STP2 terminal for 5 seconds or more.


·

STOP fuse

·

Harness or connector

·

BRK LP relay (Brake light relay)

·

Stop light control relay assembly

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C246900E11
3.5,2.635 5.781,2.896 2.281,0.26 10 false Stop Light Control Relay Assembly 0.917,0.573 1.365,0.781 0.448,0.208 10 false STOP 3.219,0.385 4.021,0.625 0.802,0.24 10 false from Battery 3.563,2 3.729,2.177 0.167,0.177 10 false 8 3.563,1.688 3.719,1.906 0.156,0.219 10 false 6 3.833,1.781 4.135,1.979 0.302,0.198 10 false +B 4.604,1.948 4.979,2.156 0.375,0.208 10 false GND 4.188,1.427 4.333,1.594 0.146,0.167 10 false 2 4.24,1.698 4.604,1.896 0.365,0.198 10 false STP 0.76,2.271 1.74,2.469 0.979,0.198 10 false ECU-IG No. 2 5.083,1.854 5.229,2.031 0.146,0.177 10 false 4 3.833,2.115 4.188,2.302 0.354,0.188 10 false OUT 1.729,1.375 3.573,1.615 1.844,0.24 10 false Stop Light Switch Assembly 2.938,0.75 3.167,0.948 0.229,0.198 10 false 1 1.74,0.76 1.927,0.948 0.188,0.188 10 false 2 3.25,5.656 4.198,5.979 0.948,0.323 10 false to Stop Lights 5.958,5.24 6.375,5.427 0.417,0.188 10 false STP2 5.958,0.875 6.344,1.083 0.385,0.208 10 false STP 5.677,0.76 5.865,0.969 0.188,0.208 10 false 7 5.646,5.135 5.844,5.323 0.198,0.188 10 false 45 5.938,3.844 6.458,4.052 0.521,0.208 10 false STPO 5.635,3.75 5.885,3.948 0.25,0.198 10 false 16 2.917,3.115 3.083,3.302 0.167,0.188 10 false 4 5.333,5.823 7.052,6.177 1.719,0.354 10 false Skid Control ECU (Master Cylinder Solenoid) 5.344,5.625 5.667,5.781 0.323,0.156 10 false A24 3.5,2.479 3.854,2.677 0.354,0.198 10 false A39 1.74,1.208 2.031,1.385 0.292,0.177 10 false A30 2.073,2.104 3.188,2.375 1.115,0.271 10 false from IG Circuit 2.927,3.75 3.083,3.948 0.156,0.198 10 false 2 1.74,3.719 1.938,3.906 0.198,0.188 10 false 1 1.74,3.26 1.917,3.458 0.177,0.198 10 false 3 2.917,3.427 3.219,3.615 0.302,0.188 10 false 5 1.406,4.229 3.573,4.5 2.167,0.271 10 false BRK LP Relay (Brake Light Relay) 1.135,5.875 1.427,6.083 0.292,0.208 10 false K33 1.313,5.552 1.49,5.76 0.177,0.208 10 false 1 1.969,5.542 2.115,5.74 0.146,0.198 10 false 2 1.115,6.073 2.313,6.323 1.198,0.25 10 false Diode (Stop Light)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off




OK

2.READ VALUE USING GTS (STOP LIGHT SW)

NG

6.CHECK HARNESS AND CONNECTOR (+B/GND TERMINAL)
2.READ VALUE USING GTS (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON and OFF according to brake pedal operation.




OK

3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

NG

11.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay BRK LP relay (Brake light relay) Relay ON/OFF Observe the stop lights (the stop lights do not come on for 2 to 5 seconds).


f.

While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output BRK LP relay (Brake light relay) output / ON or OFF ON: Relay output on (Stop lights on)
OFF: Relay output off (Stop lights off)
-

Result
Result Proceed to
When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off A
When Active Test performed, Data List item changes between ON and OFF, but stop lights do not turn on B



A

4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

B

12.INSPECT BRK LP RELAY
4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
U164977E01
0.262,0.702 0.536,0.865 0.274,0.163 10 A24 0.128,0.038 2.553,0.393 2.426,0.354 10 *a 2.848,0.587 3.247,0.764 0.399,0.177 10 STP2 2.535,1.514 2.634,0.664 2.634,0.664 2.814,0.664 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-45 (STP2) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

6.CHECK HARNESS AND CONNECTOR (+B/GND TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the stop light control relay assembly connector.


c.
U156208E03
1.083,1.479 0.271,1.625 0.271,1.625 0.271,1.708 false 1.76,1.448 2.729,0.688 2.729,0.688 2.823,0.688 false 0.125,0.135 0.354,0.417 0.229,0.281 10 false *a 1.625,0.26 1.917,0.479 0.292,0.219 10 false A39 2.917,0.583 3.156,0.75 0.24,0.167 10 false +B 0.115,1.781 0.479,1.958 0.365,0.177 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-6 (+B) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-4 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control Relay Assembly)



OK

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the stop light control relay assembly connector.


c.
U164959E02
1.375,1.198 0.281,1.625 0.281,1.625 0.281,1.708 false 0.094,0.125 0.313,0.365 0.219,0.24 10 false *a 1.615,0.25 1.938,0.448 0.323,0.198 10 false A39 0.146,1.76 0.51,1.938 0.365,0.177 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-2 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control Relay Assembly)



OK

8.INSPECT BRK LP RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRK LP RELAY
a.

Remove the BRK LP relay (brake light relay) from the engine room relay block.


b.
A087121E42
2.333,0.625 2.333,0.313 false 2.479,1.135 2.948,1.135 false 2.49,1.635 2.958,1.635 false 2.031,0.625 1.854,0.313 false 2.615,0.615 2.792,0.302 false 0.333,1.427 0.531,1.635 0.198,0.208 10 false 1 1.792,0.104 1.99,0.313 0.198,0.208 10 false 1 1.323,1.427 1.521,1.635 0.198,0.208 10 false 2 2.76,0.104 2.958,0.313 0.198,0.208 10 false 2 0.333,0.885 0.531,1.094 0.198,0.208 10 false 3 3.01,1.542 3.208,1.75 0.198,0.208 10 false 3 0.938,0.417 1.135,0.625 0.198,0.208 10 false 4 2.302,0.104 2.5,0.313 0.198,0.208 10 false 4 1.313,0.875 1.51,1.083 0.198,0.208 10 false 5 3.01,1.031 3.208,1.24 0.198,0.208 10 false 5 0.156,0.135 0.385,0.365 0.229,0.229 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 10 kΩ or higher
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 Below 1 Ω
3 - 5 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 Below 1 Ω
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 10 kΩ or higher


Text in Illustration
*1 BRK LP Relay (Brake Light Relay)



OK

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - BRK LP RELAY)

NG

REPLACE BRAKE LIGHT RELAY

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - BRK LP RELAY)
a.

Turn the ignition switch off.


b.

Disconnect the A39 stop light control relay assembly connector.


c.

Remove the BRK LP relay (brake light relay) from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-8 (OUT) - Engine room relay block BRK LP relay (brake light relay) terminal 4 Always Below 1 Ω
A39-8 (OUT) - Body ground Always 10 kΩ or higher




OK

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT POWER SOURCE TERMINAL)
a.

Remove the BRK LP relay (brake light relay) from the engine room relay block.


b.
C259268E01
0.412,1.167 0.614,1.337 0.202,0.170 12 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Component without BRK LP Relay (Brake Light Relay)
(Engine Room Relay Block)



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK BRK LP RELAY TERMINAL 3 CIRCUIT)

NG

REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
U156220E02
1.688,1.125 2.458,0.667 true 0.281,0.698 0.552,0.865 0.271,0.167 10 false A24 0.167,0.083 0.469,0.344 0.302,0.26 10 false *a 2.51,0.563 2.865,0.75 0.354,0.188 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

12.INSPECT BRK LP RELAY
a.

Remove the BRK LP relay (brake light relay) from the engine room relay block.


b.
A087121E42
2.333,0.625 2.333,0.313 false 2.479,1.135 2.948,1.135 false 2.49,1.635 2.958,1.635 false 2.031,0.625 1.854,0.313 false 2.615,0.615 2.792,0.302 false 0.333,1.427 0.531,1.635 0.198,0.208 10 false 1 1.792,0.104 1.99,0.313 0.198,0.208 10 false 1 1.323,1.427 1.521,1.635 0.198,0.208 10 false 2 2.76,0.104 2.958,0.313 0.198,0.208 10 false 2 0.333,0.885 0.531,1.094 0.198,0.208 10 false 3 3.01,1.542 3.208,1.75 0.198,0.208 10 false 3 0.938,0.417 1.135,0.625 0.198,0.208 10 false 4 2.302,0.104 2.5,0.313 0.198,0.208 10 false 4 1.313,0.875 1.51,1.083 0.198,0.208 10 false 5 3.01,1.031 3.208,1.24 0.198,0.208 10 false 5 0.156,0.135 0.385,0.365 0.229,0.229 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 10 kΩ or higher
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 Below 1 Ω
3 - 5 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 Below 1 Ω
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 10 kΩ or higher


Text in Illustration
*1 BRK LP Relay (Brake Light Relay)



OK

13.CHECK HARNESS AND CONNECTOR (BRK LP RELAY POWER SOURCE TERMINAL)

NG

REPLACE BRAKE LIGHT RELAY

13.CHECK HARNESS AND CONNECTOR (BRK LP RELAY POWER SOURCE TERMINAL)
a.

Remove the BRK LP relay (brake light relay) from the engine room relay block.


b.
C259268E01
0.412,1.167 0.614,1.337 0.202,0.170 12 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 - Body ground Ignition switch ON 8 to 14 V
5 - Body ground Always 11 to 14 V


Text in Illustration
*a Component without BRK LP relay (Brake Light Relay)
(Engine Room Relay Block)



OK

14.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
U164978E02
2.635,1.135 2.844,0.771 true 0.156,0.083 0.365,0.281 0.208,0.198 10 false *a 2.896,0.635 3.323,0.813 0.427,0.177 10 false STPO 0.198,0.781 0.479,0.979 0.281,0.198 10 false A24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A24-16 (STPO) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

15.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C