Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1421  Open or Short in Master Cylinder Pressure Sensor  C1281  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  C1423  Master Cylinder Pressure Sensor Zero Point Low Malfunction  C1424  Master Cylinder Pressure Sensor Output Malfunction  C1455  Open or Short in Control Pressure Sensor  C1457  Control Pressure Sensor Zero Point Low  C1458  Control Pressure Sensor Zero Point Output  


DESCRIPTION

The pressure control sensor and master cylinder pressure sensor are connected to the skid control ECU in the master cylinder solenoid.

C215180E15
3.26,0.469 3.771,0.708 0.51,0.24 10 false VCTRL 3.25,0.802 3.802,1.031 0.552,0.229 10 false PCTRL 3.063,1.135 3.844,1.354 0.781,0.219 10 false CTRLGND 5.344,2.115 5.823,2.323 0.479,0.208 10 false VM/C1 5.344,2.458 5.813,2.656 0.469,0.198 10 false PM/C1 5.344,2.781 6.042,2.969 0.698,0.188 10 false M/C1GND 3.271,2.094 3.958,2.406 0.688,0.313 10 false VM/C1 3.271,2.458 3.875,2.698 0.604,0.24 10 false PM/C1 3.083,2.771 3.906,3.042 0.823,0.271 10 false M/C1GND 4.656,3.146 6.813,3.365 2.156,0.219 10 false Master Cylinder Pressure Sensor 2.396,3.135 3.594,3.354 1.198,0.219 10 false Skid Control ECU 3.625,3.792 5.323,4.031 1.698,0.24 10 false Master Cylinder Solenoid 1.021,4.271 5.5,4.49 4.479,0.219 10 false VCTRL: Pressure Control Sensor Power Supply Output 1.021,4.625 5.802,4.833 4.781,0.208 10 false PCTRL: Pressure Control Sensor Signal Input 1.021,4.979 4.156,5.188 3.135,0.208 10 false CTRLGND: Pressure Control Sensor Ground 1.021,5.479 5.021,5.677 4,0.198 10 false VM/C1: Master Cylinder Pressure Sensor Power Supply Output 1.021,5.833 4.438,6.063 3.417,0.229 10 false PM/C1: Master Cylinder Pressure Sensor Signal Input 1.021,6.188 4.417,6.427 3.396,0.24 10 false M/C1GND: Master Cylinder Pressure Sensor Ground 2.313,0.74 2.583,0.927 0.271,0.188 10 false IG1 2.313,1.323 2.76,1.573 0.448,0.25 10 false STP 2.313,2.156 2.823,2.385 0.51,0.229 10 false GND 0.365,0.688 1.385,0.927 1.021,0.24 10 false from IG Circuit 0.26,1.26 1.385,1.729 1.125,0.469 10 false from Stop Light Switch Assembly 0.313,2.156 1.396,2.427 1.083,0.271 10 false to Body Ground 4.979,1.5 6.604,1.75 1.625,0.25 10 false Pressure Control Sensor 5.354,0.458 5.833,0.677 0.479,0.219 10 false VCTRL 5.344,0.813 5.875,0.99 0.531,0.177 10 false PCTRL 5.333,1.146 6.115,1.365 0.781,0.219 10 false CTRLGND

DTC Code DTC Detection Condition Trouble Area
C1421 Either condition is met:
Both of the following conditions continue for at least 1.2 seconds.
·

The IG1 terminal voltage is between 9.5 V and 17.0 V.

·

The VM/C1 terminal voltage is not within 4.4 V and 5.6 V.


Both of the following conditions continue for at least 1.2 seconds.
·

The VM/C1 terminal voltage is between 4.4 V and 5.6 V.

·

The PM/C1 terminal voltage is not within 0.19 V and 4.57 V.


Master cylinder solenoid
C1423 Both of the following conditions continue for at least 5 seconds
·

The stop light switch is off.


·

The PM/C1 terminal voltage is below 0.3 V.


Master cylinder solenoid
C1424 One of the following conditions is met:
·

Noise occurs in the signal from the PM/C1 terminal 7 times or more within 5 seconds.

·

When the vehicle speed drops from 40 km/h (25 mph) to 10 km/h (6 mph), the master cylinder pressure does not change by at least 0.048 MPa.

·

At a vehicle speed of 7 km/h (4 mph) or more, the PM/C1 terminal voltage is between 0.86 and 1.0 V and master cylinder pressure does not change by at least 0.048 MPa for 60 seconds or more.

·

At a vehicle speed of 7 km/h (4 mph) or more, the PM/C1 terminal voltage is 1.0 V or more and master cylinder pressure does not change by at least 0.048 MPa for 30 seconds or more.

·

At a vehicle speed of 7 km/h (4 mph) or more with the stop light switch ON, a state in which the pressure sensor input value is sufficiently higher than the estimated master pressure continues for 1 second or more and this state occurs 5 or more times each time the ignition switch is turned to ON, and this occurs 8 or more times consecutively.


Master cylinder solenoid
C1281 Detected only during Test Mode Master cylinder solenoid
C1455 The IG1 terminal voltage is 9.5 V or higher and the PCTRL terminal voltage is outside the range of 0.19 to 4.57 V for 1.2 seconds. Master cylinder solenoid
C1457 The PCTRL terminal voltage is below 0.3 V for 5 seconds. Master cylinder solenoid
C1458 One of the following conditions is met:
·

When the vehicle speed is 10 km/h (6 mph) or more, noise occurs in the signal from the PCTRL terminal 7 times or more within 5 seconds.

·

When the vehicle speed drops from 40 km/h (25 mph) to 0 km/h (0 mph), the control pressure does not change by at least 0.048 MPa, and this occurs 5 times.

·

At a vehicle speed of 7 km/h (4 mph) or more, the PCTRL terminal voltage is between 0.86 and 1.0 V and control pressure does not change by at least 0.048 MPa for 60 seconds or more.

·

At a vehicle speed of 7 km/h (4 mph) or more, the PCTRL terminal voltage is 1.0 V or higher and control pressure does not change by at least 0.048 MPa for 30 seconds or more.

·

At a vehicle speed of 7 km/h (4 mph) or more with the stop light switch ON, a state in which the pressure control sensor input value is sufficiently higher than the estimated control pressure continues for 1 second or more and this state occurs 5 or more times each time the ignition switch is turned to ON, and this occurs 8 or more times consecutively.


Master cylinder solenoid

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.REPLACE MASTER CYLINDER SOLENOID

NEXT

END