The skid control ECU (master cylinder solenoid) receives signals from the ECM via the CAN communication system.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1437 | When the IG1 terminal voltage is 10 V or higher and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent from the ECM for 2 seconds or more. | ·
Engine control system ·
CAN communication system ·
Skid control ECU (Master cylinder solenoid) |
When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| EFI Communication Open | EFI communication open circuit detection/ Error or Normal | Normal | - |
Normal (there are no momentary interruptions).
Perform the above inspection before removing the sensor and connector.
OK
NG
Clear the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.
Check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1437 is not output | A |
| DTC C1437 is output | B |
| CAN communication system DTC is output | C |
Refer to the Engine Control System (How to Proceed with Troubleshooting) procedures:
Refer to the CAN Communication System (How to Proceed with Troubleshooting) procedures:
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU (master cylinder solenoid) and ECM (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
Check that there is no momentary interruption.
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.
Check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1437 is not output | A |
| DTC C1437 is output (for LHD) | B |
| DTC C1437 is output (for RHD) | C |
| CAN communication system DTC is output (for LHD) | D |
| CAN communication system DTC is output (for RHD) | E |
A
B
C
D
E