The solenoid relay is built into the master cylinder solenoid.
This relay supplies power to each solenoid. If the initial check is OK, after the ignition switch is turned to ON, the relay turns on.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C146E | Either condition is met:
1.
Both of the following conditions continue for at least 0.2 seconds. (a)
IG voltage is between 9.5 and 17 V. (b)
The relay contact is open when the relay is on. 2.
Both of the following conditions continue for at least 0.2 seconds. (a)
IG voltage is 9.5 V or less when the relay is on. (b)
The relay contact remains open. |
·
ABS NO. 2 fuse ·
Solenoid relay circuit ·
Master cylinder solenoid |
| C146F | The following condition continues for at least 0.2 seconds.
·
The relay contact is closed immediately after turning the ignition switch ON when the relay is off. |
Refer to DTCs C1225, C1226, C1227, C1228, C1468, C1469, C146A and C146B (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1225).
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Turn the ignition switch off.
Disconnect the skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-31 (+BS) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid]) |
OK
NG
Turn the ignition switch off.
Disconnect the skid control ECU (master cylinder solenoid) connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-1 (GND1) - Body ground | Always | Below 1 Ω |
| A24-32 (GND2) - Body ground | Always | Below 1 Ω |
| A25-4 (GND3) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid]) |
OK
NG
These codes are stored when a problem is detected in the master cylinder solenoid.
The solenoid relay is in the master cylinder solenoid.
Therefore, solenoid relay circuit inspections and relay unit inspections cannot be performed. Be sure to check if any DTC is output before replacing the master cylinder solenoid.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.
Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output (for LHD) | B |
| DTC is output (for RHD) | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C