Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1271).

DTC Code DTC Detection Condition Trouble Area
C1407
C1408
Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH/LH

·

Skid control sensor wire

·

Speed sensor circuit

·

Skid control ECU (Master cylinder solenoid)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



WIRING DIAGRAM

C217557E29
5.469,2.771 5.885,2.99 0.417,0.219 10 false A24 5.448,2.958 7.115,3.333 1.667,0.375 10 false Skid Control ECU (Master Cylinder Solenoid) 3.115,2.771 5.177,3.031 2.063,0.26 10 false Rear Skid Control Sensor Wire 3.927,0.333 4.25,0.542 0.323,0.208 10 false Nz1 3.917,1.885 4.25,2.115 0.333,0.229 10 false Nz1 2.781,0.333 3.104,0.563 0.323,0.229 10 false z19 2.771,1.875 3.063,2.063 0.292,0.188 10 false z20 0.479,0.552 2.021,0.76 1.542,0.208 10 false Rear Speed Sensor RH 0.5,2.125 2.042,2.333 1.542,0.208 10 false Rear Speed Sensor LH 2.396,0.844 2.688,1.021 0.292,0.177 10 false RR- 2.854,0.135 3.01,0.281 0.156,0.146 10 false 2 2.375,0.313 2.688,0.49 0.313,0.177 10 false RR+ 4,0.146 4.167,0.385 0.167,0.24 10 false 4 4.01,0.688 4.208,0.896 0.198,0.208 10 false 3 2.844,0.677 3.021,0.833 0.177,0.156 10 false 1 2.406,2.417 2.698,2.594 0.292,0.177 10 false RL- 2.844,1.677 3.021,1.885 0.177,0.208 10 false 2 2.375,1.865 2.667,2.042 0.292,0.177 10 false RL+ 4,1.698 4.208,1.917 0.208,0.219 10 false 2 3.99,2.25 4.208,2.427 0.219,0.177 10 false 1 2.833,2.24 3,2.406 0.167,0.167 10 false 1 6.177,0.875 6.469,1.052 0.292,0.177 10 false RR- 6.156,0.323 6.531,0.5 0.375,0.177 10 false RR+ 6.167,2.427 6.458,2.604 0.292,0.177 10 false RL- 6.167,1.875 6.458,2.052 0.292,0.177 10 false RL+ 5.865,0.208 6.031,0.406 0.167,0.198 10 false 5 5.813,0.75 6.01,0.917 0.198,0.167 10 false 19 5.802,1.729 6.031,1.948 0.229,0.219 10 false 20 5.875,2.302 6.063,2.542 0.188,0.24 10 false 6 3.927,2.448 4.26,2.698 0.333,0.25 10 false Nz1 2.781,0.875 3.031,1.094 0.25,0.219 10 false z19 3.927,0.875 4.302,1.073 0.375,0.198 10 false Nz1 2.771,2.438 3.063,2.635 0.292,0.198 10 false z20

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection/ Error or Normal Normal -
RL Speed Open Rear speed sensor LH open detection/ Error or Normal Normal -

OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.READ VALUE USING GTS (RR/RL WHEEL SPEED)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (RR/RL WHEEL SPEED)

OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

4.INSPECT SKID CONTROL SENSOR WIRE
U156224E01
0.057,0.026 0.247,0.188 0.191,0.163 10 *1 5.774,0.88 6.041,1.033 0.267,0.152 10 z19 1.14,0.843 1.384,0.995 0.243,0.152 10 z20 6.085,0.786 6.309,0.973 0.224,0.187 10 *A 1.433,0.73 1.672,0.913 0.239,0.184 10 *B 3.453,0.71 3.727,0.863 0.274,0.152 10 Nz1 1.666,2.099 2.003,2.262 0.336,0.163 10 RL+ 0.711,2.089 1.048,2.252 0.336,0.163 10 RL- 6.297,2.11 6.633,2.273 0.336,0.163 10 RR+ 5.337,2.11 5.674,2.273 0.336,0.163 10 RR- 1.125,1.549 0.803,1.942 0.803,1.942 0.803,2.04 false 1.431,1.562 1.776,1.935 1.776,1.935 1.778,2.032 false 5.758,1.577 5.436,1.969 5.436,1.969 5.436,2.068 false 6.065,1.59 6.41,1.962 6.41,1.962 6.412,2.06 false

Text in Illustration
*A for RH *B for LH
*1 Skid Control Sensor Wire - -

a.

Remove the skid control sensor wire (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
Nz1-4 - z19-2 (RR+) Always Below 1 Ω
Nz1-3 - z19-1 (RR-) Always Below 1 Ω
Nz1-4 - Nz1-3 Always 10 kΩ or higher
Nz1-4 - Nz1-1 Always 10 kΩ or higher
Nz1-4 - Nz1-2 Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
Nz1-2 - z20-2 (RL+) Always Below 1 Ω
Nz1-1 - z20-1 (RL-) Always Below 1 Ω
Nz1-2 - Nz1-1 Always 10 kΩ or higher
Nz1-2 - Nz1-3 Always 10 kΩ or higher
Nz1-2 - Nz1-4 Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
a.

Install the skid control sensor wire.


b.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the z19 and/or z20 speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A24-5 (RR+) - z19-2 (RR+) Always Below 1 Ω
A24-5 (RR+) - Body ground Always 10 kΩ or higher
A24-19 (RR-) - z19-1 (RR-) Always Below 1 Ω
A24-19 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A24-20 (RL+) - z20-2 (RL+) Always Below 1 Ω
A24-20 (RL+) - Body ground Always 10 kΩ or higher
A24-6 (RL-) - z20-1 (RL-) Always Below 1 Ω
A24-6 (RL-) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (RR+/RL+ TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RR+/RL+ TERMINAL)
a.

Connect the skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the speed sensor connector.


c.
U156212E04
1.885,1.208 2.802,1.323 2.802,1.323 2.802,1.427 false 0.125,0.156 0.458,0.406 0.333,0.25 10 false *a 1.542,0.156 1.854,0.365 0.313,0.208 10 false z19 1.552,0.458 1.865,0.667 0.313,0.208 10 false z20 1.885,0.063 2.073,0.219 0.188,0.156 10 false *A 1.906,0.375 2.094,0.531 0.188,0.156 10 false *B 2.635,1.469 3.135,1.813 0.5,0.344 10 false RR+*A, RL+*B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
z19-2 (RR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
z20-2 (RL+) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

C