Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1421  Open or Short in Master Cylinder Pressure Sensor  C1281  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  C1423  Master Cylinder Pressure Sensor Zero Point Low Malfunction  C1424  Master Cylinder Pressure Sensor Output Malfunction  


DESCRIPTION

The pressure control sensor and master cylinder pressure sensor are connected to the skid control ECU in the master cylinder solenoid.

C173296E05
0.344,1.708 1.385,2.031 1.042,0.323 10 false from IG Circuit 2.719,1.74 3.156,1.99 0.438,0.25 10 false IG1 3.677,1.729 4.323,1.99 0.646,0.26 10 false VM/C1 3.667,2.573 4.375,2.865 0.708,0.292 10 false PM/C1 3.458,3.417 4.594,3.698 1.135,0.281 10 false M/C1 GND 5.302,1.719 6.063,2.01 0.76,0.292 10 false VM/C1 5.292,2.563 5.927,2.802 0.635,0.24 10 false PM/C1 5.313,3.385 6.229,3.688 0.917,0.302 10 false M/C1 GND 2.708,2.573 3.188,2.813 0.479,0.24 10 false STP 2.708,3.406 3.292,3.708 0.583,0.302 10 false GND 0.292,2.573 1.344,2.938 1.052,0.365 10 false from Stop Light Switch 0.333,3.406 1.385,3.625 1.052,0.219 10 false to Body Ground 2.781,3.854 4.146,4.135 1.365,0.281 10 false Skid Control ECU 3.802,4.76 5.458,5 1.656,0.24 10 false Master Cylinder Solenoid 0.146,5.656 3.781,5.885 3.635,0.229 10 false VM/C1: Master Cylinder Pressure Sensor Power Supply 0.146,5.958 3.25,6.198 3.104,0.24 10 false PM/C1: Master Cylinder Pressure Sensor Signal 0.146,6.26 3.635,6.521 3.49,0.26 10 false M/C1 GND: Master Cylinder Pressure Sensor Ground 5.354,3.833 6.49,4.24 1.135,0.406 10 false Master Cylinder Pressure Sensor

DTC Code DTC Detection Condition Trouble Area
C1421 Either condition is met:
Both of the following conditions continue for at least 1.2 seconds.
·

The IG1 terminal voltage is between 9.5 V and 17.0 V.

·

The VM/C1 terminal voltage is not within 4.4 V and 5.6 V.


Both of the following conditions continue for at least 1.2 seconds.
·

The VM/C1 terminal voltage is between 4.4 V and 5.6 V.

·

The PM/C1 terminal voltage is not within 0.19 V and 4.57 V.


Master cylinder solenoid
C1423 Both of the following conditions continue for at least 5 seconds
·

The stop light switch is off.


·

The PM/C1 terminal voltage is below 0.3 V.


Master cylinder solenoid
C1424 One of the following conditions is met:
·

Noise occurs in the signal from the PM/C1 terminal 7 times or more within 5 seconds.

·

When the vehicle speed drops from 40 km/h (25 mph) to 10 km/h (6 mph), the master cylinder pressure does not change by at least 0.048 MPa.

·

At a vehicle speed of 7 km/h (4 mph) or more, the PM/C1 terminal voltage is between 0.86 and 1.0 V and master cylinder pressure does not change by at least 0.048 MPa for 60 seconds or more.

·

At a vehicle speed of 7 km/h (4 mph) or more, the PM/C1 terminal voltage is 1.0 V or more and master cylinder pressure does not change by at least 0.048 MPa for 30 seconds or more.

·

At a vehicle speed of 7 km/h (4 mph) or more with the stop light switch ON, a state in which the pressure sensor input value is sufficiently higher than the estimated master pressure continues for 1 second or more and this state occurs 5 or more times each time the ignition switch is turned to ON, and this occurs 8 or more times consecutively.


Master cylinder solenoid
C1281 Detected only during Test Mode Master cylinder solenoid

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.REPLACE MASTER CYLINDER SOLENOID

NEXT

END