Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1453  Reservoir Level Switch Disconnected  C1454  Reservoir Level Low  


DESCRIPTION

The brake fluid level warning switch (brake master cylinder reservoir sub-assembly) sends the appropriate signal to the skid control ECU (master cylinder solenoid) when the brake fluid level drops.

DTC Code DTC Detection Condition Trouble Area
C1453 With the ECU terminal IG1 voltage at 10 to 14 V, an open in the brake fluid level warning switch circuit continues for 2 seconds or more.
·

Brake fluid level

·

Brake fluid level warning switch (Brake master cylinder reservoir sub-assembly)

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)


C1454 The fluid level of the reservoir is below the LOW level for 40 seconds after the ignition switch is turned to ON, or for 7 seconds during pump motor operation.

WIRING DIAGRAM

C358384E01
1.063,0.76 1.219,0.958 0.156,0.198 10 false 1 3.219,0.74 3.375,0.938 0.156,0.198 10 false 2 4.167,0.729 4.323,0.927 0.156,0.198 10 false 41 4.438,1.51 4.76,1.75 0.323,0.24 10 false A24 1.25,1.594 1.573,1.833 0.323,0.24 10 false A26 1.344,0.74 1.667,0.979 0.323,0.24 10 false GND 2.792,0.74 3.115,0.979 0.323,0.24 10 false LBL 4.531,0.833 4.854,1.073 0.323,0.24 10 false LBL 1.25,1.781 3.5,2.396 2.25,0.615 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly) 4.448,1.708 6.313,2.104 1.865,0.396 10 false Skid Control ECU (Master Cylinder Solenoid)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK BRAKE FLUID LEVEL
a.

Turn the ignition switch off.


b.

Depress the brake pedal 40 times or more (until the pedal reaction feels light and pedal stroke becomes longer).


c.

Check the amount of fluid in the brake reservoir.

HINT:

When the ignition switch is turned to ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm (0.197 in.) from the level when the ignition switch is off (normal).


OK:

Brake fluid level is normal.




OK

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

CHECK AND REPAIR BRAKE FLUID LEAK

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.

Disconnect the A26 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


b.
C217215E06
0.12,0.094 0.297,0.271 0.177,0.177 10 *a 2.531,1.493 2.909,1.655 0.378,0.163 10 GND 0.503,1.499 0.804,1.690 0.302,0.191 10 LBL 1.409,1.251 0.653,1.366 0.653,1.366 0.653,1.46 false 1.974,1.266 2.668,1.374 2.668,1.374 2.668,1.439 false

Measure the resistance according to the value(s) in the table below.

HINT:

A float is placed inside the reservoir. Its position can be changed by increasing/decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (GND) - 2 (LBL) Float UP (Switch off) 1.9 to 2.1 kΩ
Float DOWN (Switch on) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch [Brake Master Cylinder Reservoir Sub-assembly])

HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the A26 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-41 (LBL) - A26-2 (LBL) Always Below 1 Ω
A24-41 (LBL) - Body ground Always 10 kΩ or higher
A26-1 (GND) - Body ground Always Below 1 Ω




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine and idle it for approximately 40 seconds.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C