Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY › from 2015.08
RM2660E _54 Brake _052823 PARKING BRAKE _0255436 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 1.INSTALL PARKING BRAKE ANCHOR BLOCK

a.
C172176

Install the anchor block with the 2 nuts.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)


Hide 46430 2.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C170909

Connect the No. 3 parking brake cable with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 3.INSTALL PARKING BRAKE SHOE LEVER LH

a.
U156181E03
0.323,2.719 0.781,2.875 0.458,0.156 10 false for LH: 1.938,2.719 2.396,2.875 0.458,0.156 10 false for RH: 0.417,2.219 2,2.396 1.583,0.177 10 false High temperature grease

Apply high temperature grease to the parking brake anchor block.


b.

Install the parking brake shoe lever to the No. 3 parking brake cable.

NOTICE:

Be carefully to distinguish between the parking brake shoe lever RH and LH.



Hide 46590 4.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

a.

Apply high temperature grease to the areas of the backing plate that contact the shoe.


b.
C172175E03
1.438,1.417 0.615,1.417 true 0.281,1.354 0.594,1.51 0.313,0.156 10 false SST

Using SST, install the No. 2 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

SST
09718-00011  


Hide 46580 5.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

a.

Apply high temperature grease to the areas of the backing plate that contact the shoe.


b.
U164673E01
0.484,1.757 2.089,1.948 1.604,0.191 10 High temperature grease

Apply high temperature grease to the thread and all joining areas of the parking brake shoe adjuster screw set.


c.
C172179

Set the No. 1 parking brake shoe and shoe adjuster screw set in place.


d.
C172180

Connect the tension spring.


e.
C172174E02
2.448,0.802 2.573,0.198 2.573,0.198 2.729,0.198 true 2.781,0.125 3.094,0.271 0.313,0.146 10 false SST

Using SST, install the shoe hold down spring pin, compression spring and shoe hold down spring cup.

SST
09718-00011  


Hide 6.INSTALL PARKING BRAKE SHOE RETURN SPRING

a.
C172171E02
2.271,0.76 2.74,0.229 2.74,0.229 2.865,0.229 true 2.938,0.156 3.26,0.313 0.323,0.156 10 false SST

Using SST, install the shoe return spring.

SST
09703-30011  


Hide 7.CHECK PARKING BRAKE INSTALLATION

a.

Check that each part is installed properly.

C172182E01
0.189,0.088 0.651,0.285 0.461,0.198 10 for LH: 4.146,0.088 4.607,0.285 0.461,0.198 10 for RH: 1.123,3.268 1.497,3.448 0.373,0.179 10 Front 5.733,3.268 6.106,3.448 0.373,0.179 10 Front


Hide 42431 8.INSTALL REAR DISC

a.
C172168E09
1.875,0.969 1.875,0.25 1.875,0.25 2.458,0.25 true 1.896,1.042 2.188,1.042 2.188,1.042 2.188,0.26 true 2.5,0.177 3.219,0.354 0.719,0.177 10 true Matchmark

While aligning the matchmarks, install the rear disc.


Hide 9.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C172183

Connect the rear disc brake cylinder with 2 new bolts.

Torque:
154 N*m (1570 kgf*cm, 114 ft.*lbf)

NOTICE:
·

Do not twist the brake hose.

·

Make sure that the bolts are free from damage and foreign matter.

·

Do not overtighten the bolts.




Hide 10.ADJUST PARKING BRAKE

Hide 11.INSTALL REAR WHEEL LH

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)