Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for 3UR-FE) › 2014.08–2015.08
RM2660E _55 Steering _052824 POWER ASSIST SYSTEMS _0255440 VANE PUMP(for 3UR-FE) A

POWER ASSIST SYSTEMS  VANE PUMP(for 3UR-FE)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When installing parts, coat the parts indicated by arrows with power steering fluid (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 3UR-FE)>COMPONENTS).


PROCEDURE

Hide 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.

Coat the lip of a new oil seal with power steering fluid.


b.
C228151E01
0.227,0.175 0.528,0.335 0.301,0.160 10 SST 2.785,0.571 3.086,0.731 0.301,0.160 10 SST 0.996,0.44 0.598,0.268 0.598,0.268 0.976,0.826 false 2.541,0.729 2.744,0.66 2.744,0.66 2.618,1.016 false

Using SST and a press, press in the oil seal.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

NOTICE:

Make sure that the oil seal is installed facing in the correct direction as shown in the illustration.



Hide 2.INSTALL VANE PUMP SHAFT WITH VANE PUMP PULLEY

a.
C114703E06
1.615,1 1.615,0.125 1.615,0.125 1.458,0.125 false 0.448,0.031 1.469,0.208 1.021,0.177 10 false Protective Tape

Coat the inside surface of the bushing in the vane pump front housing with power steering fluid.


b.

Gradually insert the vane pump shaft with vane pump pulley.

NOTICE:
·

Do not damage the lip of the oil seal in the front housing.

·

Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.




Hide 3.INSTALL VANE PUMP FRONT SIDE PLATE

a.
C132035

Coat a new O-ring with power steering fluid and install it into the front housing.


b.
C107035

Coat a new O-ring with power steering fluid and install it onto the front side plate.


c.
C132040E02
2.726,1.03 1.861,1.03 false 2.642,2.765 2.009,2.765 2.009,2.765 2.009,1.03 false 1.471,0.931 1.832,1.096 0.362,0.165 10 Align

Align the notch of the front side plate with the notch of the front housing, and install the front side plate.

NOTICE:

Make sure that the front side plate is installed facing in the correct direction.



Hide 4.INSTALL VANE PUMP CAM RING

a.
C139139E02
1.281,1.043 1.673,1.212 0.392,0.170 10 Align 2.863,1.137 1.707,1.137 false 2.612,2.71 1.944,2.71 1.944,2.71 1.944,1.137 false 1.359,0.596 1.815,0.14 1.815,0.14 2.124,0.14 false 2.167,0.046 3.125,0.215 0.958,0.170 10 Inscribed Mark

Align the notch of the cam ring with the notch of the front side plate, and install the cam ring with the inscribed mark facing upward.

NOTICE:

Make sure that the cam ring is installed facing in the correct direction.



Hide 5.INSTALL VANE PUMP ROTOR

a.
C107038

Install the vane pump rotor.

HINT:

The vane pump rotor can be installed in both directions.



b.

Coat the 10 vane pump plates with power steering fluid.


c.
C141370E01
0.165,2.07 0.724,2.212 0.559,0.142 10 Outward 0.809,0.171 1.257,0.487 0.448,0.316 10 Round End 0.375,1.098 0.612,0.249 0.612,0.249 0.766,0.249 false

Install the vane pump plates with the round end facing outward.

NOTICE:

Make sure that the vane pump plates are installed facing in the correct direction.



Hide 6.INSTALL VANE PUMP SHAFT SNAP RING

a.
C358297

Using a screwdriver and snap ring expander, install a new shaft snap ring onto the vane pump shaft.

NOTICE:
·

Do not expand the shaft snap ring any further than needed.

·

Make sure that the shaft snap ring is completely fit into the groove.

·

Do not damage the vane pump rotor and shaft.




Hide 7.INSTALL VANE PUMP REAR HOUSING

a.
C107040

Coat a new O-ring with power steering fluid and install it onto the rear housing.


b.
C136780E02
2.908,0.507 3.316,0.669 0.408,0.162 10 Align 1.83,0.591 2.885,0.591 false 1.833,1.105 2.386,1.105 2.386,1.105 2.386,0.591 false

Align the straight pin of the rear housing with the notches of the cam ring, front side plate and front housing.

NOTICE:

Make sure that the O-ring is not protruding anywhere when installing the vane pump rear housing.



c.
C107024

Install the rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 9.INSTALL FLOW CONTROL VALVE ASSEMBLY

a.
C228110

Coat the flow control valve with power steering fluid.


b.

Install the compression spring and flow control valve to the front housing.

NOTICE:

Do not mistake the direction of the control valve.



c.

Coat a new O-ring with power steering fluid and install it onto the pressure port union.


d.

Install the pressure port union to the front housing.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


Hide 44310 10.FIX VANE PUMP ASSEMBLY

a.
C158820E01
0.503,1.434 0.862,1.611 0.360,0.177 10 SST 0.868,1.521 1.44,1.521 false

Using SST, fix the vane pump in a vise.

SST
09630-00014  (09631-00132)


Hide 11.INSTALL POWER STEERING SUCTION PORT UNION

a.

Coat a new O-ring with power steering fluid and install it to the suction port union.


b.
C158821

Install the suction port union to the vane pump with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)