Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) › from 2015.08
RM2660E _55 Steering _052824 POWER ASSIST SYSTEMS _0255447 POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve)  Power Steering Warning Light Circuit  


DESCRIPTION

The power steering ECU is connected to the combination meter via CAN communication. If the power steering ECU detects a malfunction, the power steering warning light comes on. At this time, the vehicle enters fail-safe mode.

WIRING DIAGRAM

C216948E13
2.063,1.927 2.948,2.125 0.885,0.198 10 false from IG Circuit 3.927,2.063 4.813,2.26 0.885,0.198 10 false ECU-IG NO. 3 0.531,3.938 2.417,4.146 1.885,0.208 10 false Combination Meter Assembly 1.521,4.385 3.448,4.594 1.927,0.208 10 false CAN Communication System 5.656,3.781 6.042,3.969 0.385,0.188 10 false E102 5.646,3.938 7.01,4.156 1.365,0.219 10 false Power Steering ECU 5.76,2.917 6.146,3.104 0.385,0.188 10 false GND 5.76,1.927 6.146,2.115 0.385,0.188 10 false IG 5.563,1.802 5.688,1.99 0.125,0.188 10 false 5 5.563,2.792 5.688,2.979 0.125,0.188 10 false 3 0.542,3.792 0.927,3.979 0.385,0.188 10 false E119

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT CAN COMMUNICATION SYSTEM
a.

Check for DTCs of the CAN communication system.

for LHD

Refer to the following procedures (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DTC CHECK / CLEAR).

for RHD

Refer to the following procedures (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output. A
DTC is output. for LHD B
for RHD C



A

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)

B

C

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)
a.
U164980E01
0.067,0.021 0.259,0.177 0.193,0.156 10 *a 1.445,1.333 1.095,1.671 false 1.824,1.333 2.174,1.671 false 2.123,1.668 2.358,1.838 0.235,0.170 10 IG 0.91,1.668 1.297,1.819 0.387,0.151 10 GND 1.507,0.273 1.869,0.412 0.362,0.139 10 E102

Disconnect the power steering ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E102-5 (IG) - Body ground Engine switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E102-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU)



OK

3.PERFORM ACTIVE TEST USING GTS (METER/GAUGE SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM ACTIVE TEST USING GTS (METER/GAUGE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Perform the Active Test of the combination meter using GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
PPS Indicator Power steering warning light ON or OFF Perform the test with the vehicle stopped and the engine idling.


d.

Check that the power steering warning light operates in accordance with the Active Test.

HINT:

Reconnect the connectors and restore the vehicle to its previous condition before checking the combination meter.


OK:

The power steering warning light turns on and off in accordance with GTS operation.




OK

NG

INSPECT METER/GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)