Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255452 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Steering Lock Motor Drive Power Circuit  


DESCRIPTION

The main body ECU supplies the power to activate the motor of the steering lock actuator assembly.

The diagnosis information of the steering lock ECU is transmitted to the intelligent tester via the certification ECU (smart key ECU assembly) as the steering lock ECU is not connected to the CAN communication system.

WIRING DIAGRAM

C165587E12
1.396,1.323 1.792,1.51 0.396,0.188 10 false SLR+ 1.885,1.448 2.115,1.635 0.229,0.188 10 false 19 0.667,2.802 1,2.99 0.333,0.188 10 false E1 3.771,2.896 4.104,3.083 0.333,0.188 10 false E26 4.198,1.344 4.594,1.531 0.396,0.188 10 false IGE 3.948,1.458 4.094,1.646 0.146,0.188 10 false 3 4.188,2.323 4.583,2.51 0.396,0.188 10 false GND 5.104,1.813 6.51,2 1.406,0.188 10 false Steering Lock Motor 3.948,2.438 4.094,2.625 0.146,0.188 10 false 1 0.656,3 2.177,3.448 1.521,0.448 10 false Main Body ECU (Cowl Side Junction Block LH) 3.75,3.083 5.979,3.427 2.229,0.344 10 false Steering Lock Actuator Assembly (Steering Lock ECU)

CAUTION / NOTICE / HINT

HINT:

When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following steps to wake up the ECU:

With the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.


NOTICE:

If the steering lock actuator assembly (steering lock ECU) is replaced, with the engine switch off and the shift lever in P (for A/T), open and close the driver side door to record the current lock position into the steering lock ECU. If this is not performed, the engine may not start.


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check the problem symptom of the steering lock system.

Result
Result Proceed to
Steering lock cannot be released A
Steering lock cannot lock B



A

2.READ VALUE USING INTELLIGENT TESTER (LOCK/UNLOCK RECEIVE)

B

5.INSPECT STEERING LOCK ECU
2.READ VALUE USING INTELLIGENT TESTER (LOCK/UNLOCK RECEIVE)
a.

Use the Data List to check if the steering lock command is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Lock/Unlock Receive Steering lock command reception record/YES or NO YES: Steering lock/unlock signal received
NO: Steering lock/unlock signal not received
-


OK:

YES is displayed on the intelligent tester screen.



OK

3.INSPECT STEERING LOCK ECU

NG

GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) (HOW TO PROCEED WITH TROUBLESHOOTING)

3.INSPECT STEERING LOCK ECU
U164603E02
2.583,2.813 2.469,2.813 2.469,2.813 2.229,2.052 true 1.51,2.813 1.615,2.813 1.615,2.813 1.865,2.052 true 0.375,0.281 2.719,0.646 2.344,0.365 10 false Component with harness connected: (Steering Lock ECU) 2.667,2.729 3.167,2.927 0.5,0.198 10 false GND 1.188,2.729 1.51,2.927 0.323,0.198 10 false IGE 0.271,1.906 0.646,2.135 0.375,0.229 10 false E26

a.

Immediately after turning the engine switch on (IG), measure the voltage between terminals E26-3 (IGE) and E26-1 (GND) of the steering lock ECU.

Result
Result Proceed to
11 to 14 V (measured voltage never becomes below 1 V) A
Below 1 V B



A

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - MAIN BODY ECU)

B

GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) (PROBLEM SYMPTOMS TABLE)

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - MAIN BODY ECU)
U164595E02
4.188,2.49 4.271,2.49 4.271,2.49 5.042,1.823 true 0.958,2.323 1.052,2.323 1.052,2.323 1.385,2.042 true 1.688,0.917 2.063,1.146 0.375,0.229 10 false E1 5.094,0.917 5.469,1.146 0.375,0.229 10 false E26 0.573,0.135 2.979,0.5 2.406,0.365 10 false Front view of wire harness connector: (to Main Body ECU) 4.083,0.156 6.49,0.521 2.406,0.365 10 false Front view of wire harness connector: (to Steering Lock ECU) 0.531,2.24 0.948,2.438 0.417,0.198 10 false SLR+ 3.896,2.406 4.208,2.604 0.313,0.198 10 false IGE

a.

Disconnect the E26 steering lock ECU connector.


b.

Disconnect the E1 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-3 (IGE) - E1-19 (SLR+) Always Below 1 Ω
E26-3 (IGE) or E1-19 (SLR+) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STEERING LOCK ECU
U164604E02
2.583,2.813 2.469,2.813 2.469,2.813 2.229,2.052 true 1.521,2.823 1.625,2.823 1.625,2.823 1.875,2.063 true 0.396,0.24 2.74,0.604 2.344,0.365 10 false Component with harness connected: (Steering Lock ECU) 2.667,2.729 3.167,2.927 0.5,0.198 10 false GND 1.219,2.74 1.542,2.938 0.323,0.198 10 false IGE 0.26,1.906 0.635,2.135 0.375,0.229 10 false E26

a.

Move the shift lever to P (for A/T).


b.

Turn the engine switch off.


c.

Open the driver side door.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E26-3 (IGE) - E26-1 (GND) Steering lock motor operating Below 1 V
E26-3 (IGE) - E26-1 (GND) Steering lock motor not operating 11 to 14 V




OK

GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) (PROBLEM SYMPTOMS TABLE)

NG

6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - MAIN BODY ECU)
6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - MAIN BODY ECU)
U164596E02
4.208,2.49 4.292,2.49 4.292,2.49 5.063,1.823 true 0.958,2.323 1.052,2.323 1.052,2.323 1.385,2.042 true 1.688,0.927 2.063,1.156 0.375,0.229 10 false E1 5.094,0.927 5.469,1.156 0.375,0.229 10 false E26 0.51,0.208 2.917,0.573 2.406,0.365 10 false Front view of wire harness connector: (to Main Body ECU) 4,0.229 6.406,0.594 2.406,0.365 10 false Front view of wire harness connector: (to Steering Lock ECU) 0.542,2.25 0.958,2.448 0.417,0.198 10 false SLR+ 3.927,2.406 4.24,2.604 0.313,0.198 10 false IGE

a.

Disconnect the E26 steering lock ECU connector.


b.

Disconnect the E1 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-3 (IGE) - E1-19 (SLR+) Always Below 1 Ω
E26-3 (IGE) or E1-19 (SLR+) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR