Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255452 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2788  IG2 Signal Malfunction  


DESCRIPTION

The steering lock ECU determines the on/off status of the engine switch through the IG2 signal circuit.

After receiving an integration relay (IG2 relay) on signal, the steering lock ECU determines that the vehicle is moving.

The steering lock ECU does not lock the steering when it receives the integration relay (IG2 relay) on signal. This prevents the steering from being locked while the vehicle is moving.

The diagnosis information of the steering lock ECU is transmitted to the intelligent tester via the certification ECU (smart key ECU assembly) as the steering lock ECU is not connected to the CAN communication system.

DTC Code Detection Condition Trouble Area
B2788 Open or short in IG2 signal circuit
·

Steering lock actuator assembly (steering lock ECU)

·

IGN fuse

·

IG2 MAIN fuse

·

Integration relay (IG2 relay)

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

A175476E07
1.073,0.25 1.917,0.438 0.844,0.188 10 false from Battery 1.448,1.708 2.208,1.896 0.76,0.188 10 false IG2 Relay 1.021,2.052 2.115,2.24 1.094,0.188 10 false Integration Relay 2.635,2.063 3.052,2.25 0.417,0.188 10 false IG2D 3.365,1.177 3.792,1.365 0.427,0.188 10 false IGN 1.042,1.156 1.469,1.5 0.427,0.344 10 false IG2 MAIN 2.083,2.583 2.417,2.771 0.333,0.188 10 false E2 4.323,2.583 4.656,2.771 0.333,0.188 10 false E26 4.594,1.031 4.99,1.219 0.396,0.188 10 false IG2 4.365,1.146 4.51,1.333 0.146,0.188 10 false 6 2.281,0.844 2.427,1.031 0.146,0.188 10 false 8 2.271,1.688 2.417,1.875 0.146,0.188 10 false 6 2.813,1.823 3.021,2.01 0.208,0.188 10 false 11 0.708,1.698 0.854,1.885 0.146,0.188 10 false 7 0.729,0.813 0.875,1 0.146,0.188 10 false 1 0.667,1.021 0.917,1.208 0.25,0.188 10 false 1C 0.677,1.479 0.927,1.667 0.25,0.188 10 false 1B 2.208,1.479 2.458,1.667 0.25,0.188 10 false 1B 2.219,1.021 2.469,1.208 0.25,0.188 10 false 1B 4.604,2.021 5,2.208 0.396,0.188 10 false GND 5.531,1.49 6.813,1.677 1.281,0.188 10 false Steering Lock Motor 4.365,2.115 4.51,2.302 0.146,0.188 10 false 1 2.073,2.771 3.594,3.219 1.521,0.448 10 false Main Body ECU (Cowl Side Junction Block LH) 4.292,2.75 6.521,3.094 2.229,0.344 10 false Steering Lock Actuator Assembly (Steering Lock ECU)

CAUTION / NOTICE / HINT

HINT:

When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following steps to wake up the ECU:

With the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.


PROCEDURE

1.INSPECT STEERING LOCK ECU
U164602E02
2.583,2.813 2.469,2.813 2.469,2.813 2.229,2.052 true 1.021,2.813 1.125,2.813 1.125,2.813 1.375,2.052 true 0.396,0.198 2.74,0.563 2.344,0.365 10 false Component with harness connected: (Steering Lock ECU) 2.667,2.729 3.167,2.927 0.5,0.198 10 false GND 0.75,2.729 1.073,2.927 0.323,0.198 10 false IG2 0.26,1.906 0.635,2.135 0.375,0.229 10 false E26

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E26-6 (IG2) - E26-1 (GND) Engine switch off Below 1 V
E26-6 (IG2) - E26-1 (GND) Engine switch on (IG) 11 to 14 V


Result
Result Proceed to
Within specified range (for Power tilt and telescopic) A
Outside specified range B
Within specified range (for Manual tilt and telescopic) C



A

B

2.INSPECT FUSE (IGN, IG2 MAIN)

C

2.INSPECT FUSE (IGN, IG2 MAIN)
a.

Remove the IGN fuse and IG2 MAIN fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGN fuse Always Below 1 Ω
IG2 MAIN fuse Always Below 1 Ω




OK

3.INSPECT INTEGRATION RELAY (IG2 RELAY)

NG

REPLACE FUSE

3.INSPECT INTEGRATION RELAY (IG2 RELAY)
U163036E04
0.208,0.24 2.708,0.615 2.5,0.375 10 false Component without harness connected: (Integration Relay) 2.656,2.615 2.906,2.802 0.25,0.188 10 false 1A 1.313,2.625 1.563,2.813 0.25,0.188 10 false 1B 0.396,2.615 0.646,2.802 0.25,0.188 10 false 1C

a.

Remove the integration relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-8 - 1C-1 Battery voltage is applied to terminals 1B-6 and 1B-7 Below 1 Ω
1B-8 - 1C-1 Battery voltage is not applied to terminals 1B-6 and 1B-7 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - INTEGRATION RELAY (IG2 RELAY) AND BODY GROUND)

NG

REPLACE INTEGRATION RELAY (IG2 RELAY)

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - INTEGRATION RELAY (IG2 RELAY) AND BODY GROUND)
U163039E02
2.135,2.281 2.052,2.281 2.052,2.281 1.552,1.844 true 1.115,1.031 1.49,1.26 0.375,0.229 10 false E26 3.885,1.031 4.26,1.26 0.375,0.229 10 false 1B 6.073,1.031 6.448,1.26 0.375,0.229 10 false 1C 0.125,0.135 2.531,0.5 2.406,0.365 10 false Front view of wire harness connector: (to Steering Lock ECU) 3.604,0.146 6.01,0.51 2.406,0.365 10 false Front view of wire harness connector: (to Integration Relay) 2.208,2.198 2.49,2.396 0.281,0.198 10 false IG2

a.

Disconnect the E26 steering lock ECU connector.


b.

Disconnect the 1B and 1C integration relay connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
E26-6 (IG2) - 1B-8 Always Below 1 Ω
E26-6 (IG2) or 1B-8 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY (IG2 RELAY) AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY (IG2 RELAY) AND BODY GROUND)
U163037E02
0.708,2.24 0.802,2.24 0.802,2.24 1.219,1.927 true 1.635,0.969 2.01,1.198 0.375,0.229 10 false E2 5.125,0.958 5.5,1.188 0.375,0.229 10 false 1B 0.573,0.135 2.979,0.5 2.406,0.365 10 false Front view of wire harness connector: (to Main Body ECU) 4.01,0.146 6.417,0.51 2.406,0.365 10 false Front view of wire harness connector: (to Integration Relay) 0.333,2.167 0.74,2.365 0.406,0.198 10 false IG2D

a.

Disconnect the E2 main body ECU connector.


b.

Disconnect the 1B integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E2-11 (IG2D) - 1B-6 Always Below 1 Ω
1B-7 - Body ground Always Below 1 Ω
E2-11 (IG2D) or 1B-6 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR