Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255452 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2788  IG2 Signal Malfunction  


DESCRIPTION

This DTC is stored when the steering lock ECU (steering lock actuator assembly) detects an IG2 power supply malfunction.

HINT:

The steering lock ECU (steering lock actuator assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Condition Trouble Area DTC Output Confirmation Operation
B2788 Mismatch between the steering lock ECU (steering lock actuator assembly) IG2 input from the LIN communication system and from the direct line (1-trip detection logic*).
·

Steering lock ECU (Steering lock actuator assembly)

·

Harness or connector


No confirmation operation is necessary (monitoring is continuous).

*: Only output while a malfunction is present and the engine switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. -

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2788 - -

WIRING DIAGRAM

C240290E37
0.927,0.656 1.198,0.854 0.271,0.198 10 false LIN 1.26,0.5 1.448,0.698 0.188,0.198 10 false 6 5.344,2.24 5.677,2.438 0.333,0.198 10 false GND 5.375,1.448 5.708,1.646 0.333,0.198 10 false IG2 5.156,1.365 5.344,1.563 0.188,0.198 10 false 6 5.156,2.135 5.344,2.333 0.188,0.198 10 false 1 5.375,0.646 5.708,0.844 0.333,0.198 10 false LIN 5.167,0.5 5.354,0.698 0.188,0.198 10 false 5 2.792,3.344 4.427,3.594 1.635,0.25 10 false LIN Communication Line 3.906,1.635 4.594,1.792 0.688,0.156 10 false IG2 NO.1 1.406,1.417 2.792,1.667 1.385,0.25 10 false from IG2 MAIN Relay 4.854,3.198 6.677,3.677 1.823,0.479 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 0.198,3.271 1.917,3.677 1.719,0.406 10 false Certification ECU (Smart Key ECU Assembly) 4.865,3.031 5.292,3.208 0.427,0.177 10 false E26 0.208,3.104 0.542,3.292 0.333,0.188 10 false E130

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, confirm that no DTCs are output again (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR).

·

When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (refer to Service Bulletin).



PROCEDURE

1.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (POWER SOURCE MODE SIGNAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the E26 steering lock ECU (steering lock actuator assembly) connector.


c.
U156089E01
0.377,0.3 0.605,0.476 0.227,0.176 10 *a 0.429,0.986 0.738,1.128 0.309,0.142 10 E26 0.818,1.558 1.176,1.742 0.357,0.184 10 GND 1.281,2.42 1.032,1.733 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


d.

Reconnect the E26 steering lock ECU (steering lock actuator assembly) connector.


e.
U156085E01
2.281,1.979 2.76,2.823 true 1.365,1.99 0.885,2.833 true 0.375,0.271 0.635,0.479 0.26,0.208 10 false *a 0.323,0.979 0.667,1.135 0.344,0.156 10 false E26 0.75,2.854 1.083,3.01 0.333,0.156 10 false IG2 2.646,2.854 3.021,3.01 0.375,0.156 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E26-6 (IG2) - E26-1 (GND) Engine switch on (IG) 11 to 14 V
E26-6 (IG2) - E26-1 (GND) Engine switch off Below 1 V


Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))

Result
Result Proceed to
OK for Manual Tilt and Manual Telescopic Steering Column A
for Power Tilt and Power Telescopic Steering Column B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR