Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255453 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2602  Key Unlock Warning Switch Circuit Malfunction  B2606  Key Code Confirm Signal Malfunction  


DESCRIPTION

A key code confirmation signal (ON or OFF) is sent from the main body ECU to the multiplex tilt and telescopic ECU via the communication bus.

The multiplex tilt and telescopic ECU uses this signal to operate the auto away/return function.

DTC Code Detection Condition Trouble Area
B2602 Both of the following conditions continue:
·

The key code confirmation signal is off.


·

The engine switch is on (IG).


·

CAN communication system

·

Entry and start system (for start function)

·

Multiplex tilt and telescopic ECU


B2606 IG signals and/or key code confirmation signals are not received correctly.
·

CAN communication system

·

Entry and start system (for start function)

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

U164840E02
6.01,4.5 7.125,4.844 1.115,0.344 10 false Multiplex Tilt and Telescopic ECU 6.25,0.594 6.479,0.781 0.229,0.188 10 false IG 6.24,4.083 6.667,4.271 0.427,0.188 10 false GND 3.125,1.854 3.771,2.042 0.646,0.188 10 false IG1 No. 1 0.229,2.156 0.708,2.49 0.479,0.333 10 false from Battery 0.229,0.49 0.708,0.823 0.479,0.333 10 false from Battery 2.115,1.531 2.542,1.719 0.427,0.188 10 false IG1D 1.802,1.792 2.229,1.979 0.427,0.188 10 false AM1 1.802,2.281 2.229,2.469 0.427,0.188 10 false AM2 2.021,2.708 2.448,2.896 0.427,0.188 10 false CANP 2.01,3.188 2.438,3.375 0.427,0.188 10 false CANN 6.229,2.729 6.656,2.917 0.427,0.188 10 false CANP 6.229,3.208 6.656,3.396 0.427,0.188 10 false CANN 1.74,3.646 4.729,3.885 2.99,0.24 10 false Main Body ECU (Cowl Side Junction Block LH) 3.948,0.719 4.563,1.094 0.615,0.375 10 false ECU-IG1 No. 1 5.938,0.417 6.146,0.594 0.208,0.177 10 false 8 5.948,2.542 6.156,2.719 0.208,0.177 10 false 5 5.906,3.021 6.115,3.198 0.208,0.177 10 false 14 5.906,3.896 6.115,4.073 0.208,0.177 10 false 11 2.563,3.021 2.771,3.198 0.208,0.177 10 false 15 2.563,2.552 2.771,2.729 0.208,0.177 10 false 16 2.615,1.344 2.823,1.521 0.208,0.177 10 false 3 1.521,2.052 1.729,2.229 0.208,0.177 10 false 1 1.531,1.594 1.74,1.771 0.208,0.177 10 false 6 2.573,1.542 2.781,1.698 0.208,0.156 10 false E1 2.563,2.729 2.781,2.885 0.219,0.156 10 false E3 2.563,3.198 2.781,3.354 0.219,0.156 10 false E3 1.479,2.25 1.688,2.406 0.208,0.156 10 false E2 1.479,1.781 1.688,1.938 0.208,0.156 10 false E1 5.865,0.594 6.156,0.75 0.292,0.156 10 false E27 4.75,0.417 4.958,0.594 0.208,0.177 10 false 56 4.74,0.594 4.969,0.75 0.229,0.156 10 false 2D 4.75,1.365 4.958,1.542 0.208,0.177 10 false 62 4.74,1.542 4.969,1.698 0.229,0.156 10 false 2D 5.865,4.083 6.156,4.24 0.292,0.156 10 false E27 5.865,3.208 6.156,3.365 0.292,0.156 10 false E27 5.865,2.729 6.156,2.885 0.292,0.156 10 false E27 3.51,2.885 5.229,3.125 1.719,0.24 10 false CAN Communication Line

PROCEDURE

1.CHECK OTHER DTC OUTPUT
HINT:

The power tilt and power telescopic steering column system uses the CAN communication system, so check its diagnostic system before proceeding to troubleshooting.


a.

Check if DTC B2621 is output.

Result
DTC Condition Proceed to
B2621 is not output A
B2621 is output B

HINT:
·

If DTC B2621 is output, perform troubleshooting for B2621 first.

·

DTC B2621 indicates a communication interruption for the power tilt and power telescopic steering column system.





A

2.READ VALUE USING INTELLIGENT TESTER (COMMUNICATION STATE OF ENGINE SWITCH AND KEY CODE)

B

2.READ VALUE USING INTELLIGENT TESTER (COMMUNICATION STATE OF ENGINE SWITCH AND KEY CODE)
a.

Use the Data List to check if the communication of the key code and the engine switch are functioning properly.

Tilt & Telescopic
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG Switch (CAN) Communication state of engine switch/ON or OFF ON: Communication normal
OFF: Communication interrupted
-
Key Code Confirm (CAN) Communication state of key code confirmation signal/ON or OFF ON: Communication normal
OFF: Communication interrupted
-


OK:

"ON" is displayed.



OK

3.RECONFIRM DTC

NG