Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255453 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2610  Tilt Position Sensor or Tilt Motor Circuit Malfunction  


DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and outputs a signal to the CPU based on that tilt.

C152160E18
1.042,0.167 2.25,0.51 1.208,0.344 10 false Tilt Up Mechanical Lock Position 4.823,0.156 6.333,0.573 1.51,0.417 10 false Tilt Down Mechanical Lock Position 2.969,1.26 4.115,1.458 1.146,0.198 10 false Operation Range 1.313,2.042 2.625,2.313 1.313,0.271 10 false Tilt Up Limit Position 4.333,2.063 5.896,2.313 1.563,0.25 10 false Tilt Down Limit Position

HINT:

Limit positions can be confirmed on the screen of the intelligent tester.


DTC Code Detection Condition Trouble Area
B2610 The tilt operation stops within the operation range while operating.
·

Harness or connector

·

Tilt position sensor or tilt motor

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C149999E09
0.792,4.177 1.104,4.375 0.313,0.198 10 false E17 0.917,1.031 1.646,1.24 0.729,0.208 10 false Tilt Motor 1.708,0.917 2.146,1.115 0.438,0.198 10 false TIM+ 4.646,0.917 5.063,1.115 0.417,0.198 10 false TIM+ 1.729,1.708 2.167,1.906 0.438,0.198 10 false TIM- 4.656,1.719 5.031,1.917 0.375,0.198 10 false TIM- 1.771,2.469 2.094,2.667 0.323,0.198 10 false VCI 4.656,2.458 4.979,2.656 0.323,0.198 10 false VCI 1.792,2.865 2.073,3.063 0.281,0.198 10 false TIS 4.656,2.854 4.938,3.052 0.281,0.198 10 false TIS 1.833,3.281 2.083,3.479 0.25,0.198 10 false E1 4.667,3.26 4.917,3.458 0.25,0.198 10 false E1 0.49,3.385 1.781,3.604 1.292,0.219 10 false Tilt Position Sensor 2.104,0.927 2.25,1.125 0.146,0.198 10 false 1 4.365,1.417 4.51,1.615 0.146,0.198 10 false 1 2.104,1.708 2.25,1.917 0.146,0.208 10 false 2 2.104,2.458 2.25,2.656 0.146,0.198 10 false 4 2.104,2.865 2.25,3.063 0.146,0.198 10 false 5 2.104,3.271 2.271,3.469 0.167,0.198 10 false 6 4.375,2.167 4.49,2.375 0.115,0.208 10 false 6 4.385,2.573 4.5,2.781 0.115,0.208 10 false 7 4.292,0.813 4.625,1.01 0.333,0.198 10 false E27 4.292,1.604 4.625,1.802 0.333,0.198 10 false E27 4.292,2.365 4.625,2.563 0.333,0.198 10 false E27 4.292,2.75 4.625,2.948 0.333,0.198 10 false E27 4.292,3.146 4.625,3.344 0.333,0.198 10 false E27 4.292,3.542 4.625,3.74 0.333,0.198 10 false E27 4.323,0.625 4.563,0.823 0.24,0.198 10 false 10 4.333,3.365 4.573,3.563 0.24,0.198 10 false 11 4.333,2.979 4.573,3.177 0.24,0.198 10 false 17 4.646,3.646 5.052,3.844 0.406,0.198 10 false GND 6.01,0.594 6.323,0.792 0.313,0.198 10 false +B 6.01,1.406 6.323,1.604 0.313,0.198 10 false +B 6.083,2.156 6.49,2.354 0.406,0.198 10 false 12 V 5.906,3.271 6.479,3.469 0.573,0.198 10 false to CPU 4.646,4.021 6.792,4.219 2.146,0.198 10 false Multiplex Tilt and Telescopic ECU 0.792,4.344 1.521,4.542 0.729,0.198 10 false Tilt Motor

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TILT UP/DOWN)
C106468E01
1.992,0.035 2.232,0.236 0.239,0.201 10 Up 2.474,1.152 2.886,1.363 0.413,0.211 10 Down

a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering wheel tilts up and down.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Tilt Operation Tilt operation Up/Down -


Result
Result Proceed to
Steering wheel does not tilt up/down. A
Steering wheel tilts up/down. B


A

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)

B

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)
U164522E02
1.896,2.063 1.542,2.281 true 1.906,2.146 1.667,2.5 true 4.729,2.167 4.854,2.594 true 4.438,2.094 4.188,1.781 true 0.615,0.146 3,0.604 2.385,0.458 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 0.896,2.219 1.563,2.417 0.667,0.198 10 false 10 (TIM+) 4.792,2.594 5.323,2.792 0.531,0.198 10 false TIM+ 1.188,2.521 1.781,2.719 0.594,0.198 10 false 1 (TIM-) 3.99,1.583 4.438,1.781 0.448,0.198 10 false TIM- 2.042,1.115 2.333,1.313 0.292,0.198 10 false E27 3.948,2.156 4.26,2.354 0.313,0.198 10 false E17 3.833,0.156 6.198,0.583 2.365,0.427 10 false Rear view of wire harness connector: (to Tilt Motor)

a.

Disconnect the E27 multiplex tilt and telescopic ECU connector.


b.

Disconnect the E17 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E27-10 (TIM+) - E17-1 (TIM+) Always Below 1 Ω
E27-1 (TIM-) - E17-2 (TIM-)
E27-10 (TIM+) - Body ground Always 10 kΩ or higher
E27-1 (TIM-) - Body ground




OK

3.INSPECT TILT MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TILT MOTOR
C149090E09
1.542,1.115 1.094,1.229 false 2.177,1.115 2.49,0.958 false 5.521,1.115 5.885,0.969 false 4.906,1.115 4.406,1.25 false 0.604,0.135 3.094,0.531 2.49,0.396 10 false Component without harness connected: (Tilt Motor) 2.552,0.885 3.26,1.083 0.708,0.198 10 false TIM+ (+) 0.615,1.156 1.25,1.354 0.635,0.198 10 false TIM- (-) 4.063,0.115 6.552,0.51 2.49,0.396 10 false Component without harness connected: (Tilt Motor) 5.948,0.906 6.656,1.104 0.708,0.198 10 false TIM+ (-) 3.875,1.177 4.51,1.375 0.635,0.198 10 false TIM- (+)

a.

Apply 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.

OK:
Measurement Condition Specified Condition
12 V battery positive (+) lead → Terminal E17-1 (TIM+)
12 V battery negative (-) lead → Terminal E17-2 (TIM-)
The steering wheel tilts up.
12 V battery positive (+) lead → Terminal E17-2 (TIM-)
12 V battery negative (-) lead → Terminal E17-1 (TIM+)
The steering wheel tilts down.




OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
U164521E02
2.188,2.135 2.51,2.51 true 2.229,2.125 2.625,2.26 true 2.292,2.063 2.667,1.99 true 4.438,2.24 4.146,2.469 true 4.51,2.25 4.375,2.552 true 4.646,2.25 4.875,2.427 true 0.615,0.302 2.948,0.708 2.333,0.406 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 2.729,1.896 3.271,2.094 0.542,0.198 10 false 17 (E1) 2.677,2.26 3.292,2.458 0.615,0.198 10 false 7 (TIS) 2.042,1.104 2.333,1.302 0.292,0.198 10 false E27 3.948,2.156 4.26,2.354 0.313,0.198 10 false E17 3.813,0.313 6.125,0.792 2.313,0.479 10 false Rear view of wire harness connector: (to Tilt Motor) 2.51,2.521 3.146,2.719 0.635,0.198 10 false 6 (VCI) 3.938,2.458 4.302,2.656 0.365,0.198 10 false E1 4.281,2.563 4.594,2.76 0.313,0.198 10 false TIS 4.802,2.448 5.115,2.646 0.313,0.198 10 false VCI

a.

Disconnect the E27 multiplex tilt and telescopic ECU connector.


b.

Disconnect the E17 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E27-6 (VCI) - E17-4 (VCI) Always Below 1 Ω
E27-7 (TIS) - E17-5 (TIS)
E27-17 (E1) - E17-6 (E1)
E27-6 (VCI) - Body ground Always 10 kΩ or higher
E27-7 (TIS) - Body ground
E27-17 (E1) - Body ground




OK

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
U164516E02
1.854,2.615 1.281,3.021 true 0.125,0.167 2.49,0.615 2.365,0.448 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 0.854,3.052 1.5,3.25 0.646,0.198 10 false 11 (GND) 1.969,1.313 2.26,1.51 0.292,0.198 10 false E27

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E27-11 (GND) - Body ground Always Below 1 Ω




OK

6.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)
a.
U164523E02
0.792,2.552 0.406,2.771 true 0.958,2.573 0.573,3.063 true 1.146,2.573 1.469,3.01 true 0.115,0.104 2.417,0.594 2.302,0.49 10 false Rear view of wire harness connector: (to Tilt Motor) 0.208,2.188 0.49,2.385 0.281,0.198 10 false E17 1.49,3.042 1.813,3.24 0.323,0.198 10 false VCI 0.448,3.104 0.75,3.302 0.302,0.198 10 false TIS 0.188,2.719 0.438,2.917 0.25,0.198 10 false E1

Reconnect the E27 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E17-4 (VCI) - E17-6 (E1) Engine switch on (IG) 8 to 16 V
E17-5 (TIS) - E17-6 (E1)




OK

7.CHECK TILT POSITION SENSOR

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

7.CHECK TILT POSITION SENSOR
a.
U164520E02
2.375,1.99 2.604,1.604 true 2.302,2.094 2.844,2.667 true 2.646,1.448 3.125,1.646 0.479,0.198 10 false 17 (E1) 2.906,2.625 3.365,2.823 0.458,0.198 10 false 7 (TIS) 2.094,1.417 2.385,1.615 0.292,0.198 10 false E27 0.167,0.135 2.656,0.531 2.49,0.396 10 false Component with harness connected: (Multiplex Tilt and Telescopic ECU)

Reconnect the E17 tilt motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E27-7 (TIS) - E27-17 (E1) Steering tilting up or tilting down Pulse generation
High: 8 to 16 V
Low: Below 1 V




OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)