Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255455 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

a.

Disable the AUTO TILT AWAY function by changing the customize parameter (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS).

NOTICE:

Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.


HINT:

Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.



b.

Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.


c.

Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 45187 3.REMOVE LOWER NO. 3 STEERING WHEEL COVER

Hide 45186 4.REMOVE LOWER NO. 2 STEERING WHEEL COVER

Hide 45100 6.REMOVE STEERING WHEEL ASSEMBLY

Hide 7.REMOVE LOWER STEERING COLUMN COVER

a.
C172674

Remove the 3 screws.


b.

Detach the 2 claws to remove the lower steering column cover.

NOTICE:

Do not damage the tilt and telescopic switch.



Hide 45286B 8.REMOVE UPPER STEERING COLUMN COVER

a.
C172675

Detach the 4 clips.


b.

Detach the claw to remove the upper steering column cover.


Hide 89235A 9.REMOVE TILT AND TELESCOPIC SWITCH

a.
C159804

Disconnect the switch connector.


b.

Using a screwdriver, detach the claw and pull out the switch.

NOTICE:

Pushing on the claw too hard will break the claw.


HINT:

Tape the screwdriver tip before use.



Hide 10.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.
C172676

Disconnect the 5 connectors from the turn signal switch with spiral cable.


b.
U164696

Using pliers, grip the claws of the clamp and remove the turn signal switch with spiral cable from the steering column.


Hide 55449C 11.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

Hide 55403C 12.REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

Hide 55474C 14.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55475A 15.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55404C 16.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

Hide 55404C 17.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

Hide 55606 19.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

Hide 55432D 21.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 73900 23.REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55606 24.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

Hide 25.REMOVE WIRE HARNESS PROTECTOR AND WIRE HARNESS

a.
C172657

Detach the 3 claws to remove the wire harness protector and wire harness.


Hide 45810 27.REMOVE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

a.
C179299E02
0.826,0.479 1.009,0.639 0.183,0.160 10 *a 1.57,0.576 1.039,0.576 false 1.537,0.779 1.039,0.576 false

Put matchmarks on the steering actuator and steering column.

Text in Illustration
*a Matchmark


b.

Remove the bolt.


c.
C172653

Remove the 4 nuts and steering column.


Hide 45240J 28.DISCONNECT STEERING ACTUATOR ASSEMBLY

Hide 45026D 29.REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C179099

Remove the 4 bolts and nut with the steering column hole cover from the vehicle.


Hide 45203A 30.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT

a.
C358214E01
0.708,1.604 0.885,0.427 0.885,0.427 1.188,0.427 false 0.802,1.573 1.052,0.438 false 1.26,0.333 1.573,0.531 0.313,0.198 10 false *a 2.667,1.135 2.844,1.323 0.177,0.188 10 false A

Loosen the bolt and remove the No. 2 intermediate shaft.

Text in Illustration
*a Matchmark

NOTICE:

It is possible to install the intermediate shaft to the same position it was removed from without placing matchmarks due to the dust cover part labeled A. Therefore, do not remove the dust cover from the steering link.


HINT:

If the dust cover is removed/installed or replaced, place matchmarks on the dust cover and steering link.