Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255453 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2610  Tilt Position Sensor or Tilt Motor Circuit Malfunction  


DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and sends a signal to the multiplex tilt and telescopic ECU based on that angle.

DTC No. Detection Item Trouble Area
B2610 Tilt operation stops within the operation range while operating.
·

TI & TE fuse

·

Tilt position sensor or tilt motor

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C244371E37
0.979,1.458 1.708,1.698 0.729,0.24 10 false Tilt Motor 0.49,3.781 1.792,4.01 1.302,0.229 10 false Tilt Position Sensor 2.125,0.802 2.906,1.042 0.781,0.24 10 false from Battery 3.542,0.969 3.958,1.167 0.417,0.198 10 false TI&TE 4.688,0.823 4.958,1.083 0.271,0.26 10 false +B 4.677,1.135 5.104,1.292 0.427,0.156 10 false TIM+ 4.677,1.927 5.115,2.135 0.438,0.208 10 false TIM- 4.688,2.677 4.958,2.875 0.271,0.198 10 false VCI 4.688,3.073 4.958,3.271 0.271,0.198 10 false TIS 4.688,3.469 4.885,3.667 0.198,0.198 10 false E1 1.677,1.115 2.104,1.333 0.427,0.219 10 false TIM+ 1.688,1.917 2.104,2.073 0.417,0.156 10 false TIM- 1.75,2.677 2.021,2.875 0.271,0.198 10 false VCI 1.76,3.073 2.031,3.271 0.271,0.198 10 false TIS 1.813,3.469 2.01,3.667 0.198,0.198 10 false E1 4.667,3.865 5.094,4.073 0.427,0.208 10 false GND2 4.688,4.406 5.052,4.656 0.365,0.25 10 false GND 4.656,4.823 5.073,5 0.417,0.177 10 false E144 0.76,4.802 1.021,5 0.26,0.198 10 false E17 0.76,5 1.563,5.208 0.802,0.208 10 false Tilt Motor 4.656,5.021 6.729,5.281 2.073,0.26 10 false Multiplex Tilt and Telescopic ECU 5.99,3.667 6.552,3.885 0.563,0.219 10 false to CPU 6.073,2.958 6.427,3.146 0.354,0.188 10 false 12 V 6.031,1.75 6.25,1.938 0.219,0.188 10 false +B 6.031,0.948 6.25,1.135 0.219,0.188 10 false +B 4.49,0.729 4.656,0.896 0.167,0.167 10 false 2 2.135,1.927 2.302,2.094 0.167,0.167 10 false 2 4.479,1.146 4.646,1.344 0.167,0.198 10 false 7 2.146,3.458 2.313,3.656 0.167,0.198 10 false 6 2.135,2.688 2.302,2.885 0.167,0.198 10 false 4 2.135,3.073 2.302,3.271 0.167,0.198 10 false 5 4.417,1.917 4.583,2.115 0.167,0.198 10 false 20 4.417,2.667 4.583,2.865 0.167,0.198 10 false 13 4.406,3.052 4.573,3.25 0.167,0.198 10 false 16 4.479,3.458 4.646,3.656 0.167,0.198 10 false 4 4.469,3.854 4.635,4.052 0.167,0.198 10 false 8 4.469,4.302 4.635,4.5 0.167,0.198 10 false 1 2.125,1.125 2.292,1.302 0.167,0.177 10 false 1

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (TILT OPERATION)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Check that the steering wheel tilts up and down. Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Tilt Operation Tilt operation UP/DOWN -

OK:

The steering wheel tilts up and down.




OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILTPOSITION SENSOR)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.
U165137E01
0.155,0.116 0.357,0.290 0.202,0.174 10 *a 1.557,0.366 1.939,0.541 0.381,0.174 10 E144 0.776,0.447 1.032,0.622 0.257,0.174 10 +B 0.981,1.001 0.904,0.639 false

Disconnect the multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E144-2 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
U165138E02
0.813,0.979 0.75,0.594 false 0.844,1.604 0.781,1.229 false 0.167,0.125 0.365,0.302 0.198,0.177 10 false *a 1.573,0.365 1.969,0.552 0.396,0.188 10 false E144 0.573,0.385 1.01,0.563 0.438,0.177 10 false GND 0.667,1.646 1.104,1.823 0.438,0.177 10 false GND2

Disconnect the multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-1 (GND) - Body ground Always Below 1 Ω
E144-8 (GND2) - Body ground


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)
a.

Disconnect the E144 multiplex tilt and telescopic ECU connector.


b.

Disconnect the E17 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-7 (TIM+) - E17-1 (TIM+) Always Below 1 Ω
E144-20 (TIM-) - E17-2 (TIM-)
E144-7 (TIM+) - Body ground 10 kΩ or higher
E144-20 (TIM-) - Body ground




OK

5.CHECK TILT MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TILT MOTOR
a.

Disconnect the E17 tilt motor connector.


b.
U117407E01
0.305,0.226 0.508,0.414 0.204,0.188 10 *a 2.069,1.112 2.386,0.666 false 2.069,1.112 2.386,0.666 false 0.587,0.555 0.935,0.740 0.348,0.185 10 TIM- 1.358,1.131 1.042,0.686 false 1.358,1.131 1.042,0.686 false 2.44,0.555 2.788,0.740 0.348,0.185 10 TIM+

Apply 12 V battery voltage to the tilt motor connector.

Then check the steering wheel tilt operation.

OK:
Measurement Condition Specified Condition
·

12 V battery positive (+) lead → Terminal 1 (TIM+)

·

12 V battery negative (-) lead → Terminal 2 (TIM-)


The steering wheel tilts up.
·

12 V battery negative (-) lead → Terminal 1 (TIM+)

·

12 V battery positive (+) lead → Terminal 2 (TIM-)


The steering wheel tilts down.


Text in Illustration
*a Component without harness connected
(Tilt Motor)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILTPOSITION SENSOR)
a.

Disconnect the E144 multiplex tilt and telescopic ECU connector.


b.

Disconnect the E17 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-13 (VCI) - E17-4 (VCI) Always Below 1 Ω
E144-16 (TIS) - E17-5 (TIS)
E144-4 (E1) - E17-6 (E1)
E144-13 (VCI) - Body ground 10 kΩ or higher
E144-16 (TIS) - Body ground
E144-4 (E1) - Body ground




OK

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODYGROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODYGROUND)
a.
U165138E02
0.813,0.979 0.75,0.594 false 0.844,1.604 0.781,1.229 false 0.167,0.125 0.365,0.302 0.198,0.177 10 false *a 1.573,0.365 1.969,0.552 0.396,0.188 10 false E144 0.573,0.385 1.01,0.563 0.438,0.177 10 false GND 0.667,1.646 1.104,1.823 0.438,0.177 10 false GND2

Disconnect the multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-1 (GND) - Body ground Always Below 1 Ω
E144-8 (GND2) - Body ground


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI TERMINAL VOLTAGE)
a.
U165143E02
1.292,0.969 1.146,0.698 false 1.896,1.458 1.854,1.177 false 0.177,0.115 0.375,0.292 0.198,0.177 10 false *a 1.563,0.385 1.99,0.573 0.427,0.188 10 false E144 1.781,1.5 2.104,1.677 0.323,0.177 10 false VCI 1.01,0.49 1.354,0.667 0.344,0.177 10 false E1

Reconnect the multiplex tilt and telescopic ECU connector.


b.

Disconnect the E17 tilt motor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E144-13 (VCI) - E144-4 (E1) Engine switch on (IG) 8 to 14 V


Text in Illustration
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)



OK

9.CHECK TILT POSITION SENSOR

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

9.CHECK TILT POSITION SENSOR
a.
U165142E02
1.292,0.969 1.146,0.698 false 1.542,1.448 1.448,1.167 false 0.167,0.115 0.365,0.292 0.198,0.177 10 false *a 1.552,0.385 1.938,0.563 0.385,0.177 10 false E144 1.458,1.5 1.802,1.677 0.344,0.177 10 false TIS 1.042,0.5 1.385,0.677 0.344,0.177 10 false E1

Reconnect the multiplex tilt and telescopic ECU connector.


b.

Reconnect the E17 tilt motor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E144-16 (TIS) - E144-4 (E1) Steering wheel tilting up or tilting down Pulse generation
High: 8 to 14 V
Low: Below 1 V


Text in Illustration
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG