Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255455 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

a.

Disable the AUTO TILT AWAY function by changing the customize parameter (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS).

NOTICE:

Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.


HINT:

Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.



b.

Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.


c.

Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 45100 3.REMOVE STEERING WHEEL ASSEMBLY

Hide 4.REMOVE LOWER STEERING COLUMN COVER

a.
C348616

Remove the 3 screws.


b.
U165626E02
0.396,0.229 1.229,0.583 0.833,0.354 10 true Push Area 2.24,0.25 3.042,0.479 0.802,0.229 10 false Push Area

While pressing the push area shown in the illustration to detach the 4 claws, slightly lower steering column cover.

NOTICE:

Do not damage the tilt and telescopic switch.



Hide 45286B 5.REMOVE UPPER STEERING COLUMN COVER

a.
C348617E01
0.145,0.694 1.069,1.045 0.924,0.350 10 Meter Hood Spacer 1.653,1.751 1.124,0.809 false

Detach the 4 clips and 2 claws remove the meter hood spacer.


b.

Detach the claw and 2 guide pin remove the upper steering column cover from the steering column assembly..


Hide 6.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.

Disconnect the connectors from the combination switch with spiral cable sub-assembly.


b.
C348618

Detach the 3 claws and remove the combination switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 73900 7.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55303B 8.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 9.REMOVE WIRE HARNESS PROTECTOR AND WIRE HARNESS

a.
C335518

Detach the 2 claws and 2 harness clamps, disconnect the wire harness protector and wire harness.


Hide 45250 11.REMOVE STEERING COLUMN ASSEMBLY

a.

w/ VGRS:

i.
C179299E02
0.826,0.479 1.009,0.639 0.183,0.160 10 *a 1.57,0.576 1.039,0.576 false 1.537,0.779 1.039,0.576 false

Put matchmarks on the steering actuator and steering column.

Text in Illustration
*a Matchmark



b.

w/o VGRS:

i.
C172648E03
1.906,1.208 2.417,0.99 2.417,0.99 1.917,0.75 true 2.469,0.906 2.729,1.125 0.26,0.219 10 false *a

Put matchmarks on the steering intermediate shaft and the steering column.

Text in Illustration
*a Matchmark



c.

Remove the bolt.


d.
C347264

Remove the 4 nuts and steering column.


Hide 45240J 12.DISCONNECT STEERING ACTUATOR ASSEMBLY

Hide 45026D 13.REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY (w/ VGRS)

a.
C179099

Remove the 4 bolts and nut with the steering column hole cover from the vehicle.


Hide 45026D 14.REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY (w/o VGRS)

a.
C358207

Hold the clamp with needle nose pliers, then insert a screwdriver and turn it in the direction shown in the illustration to remove the clamp of the steering column hole cover.


b.
C179099

Remove the 4 bolts and nut with the steering column hole cover from the vehicle.


Hide 45203A 15.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT

a.
C358214E01
0.708,1.604 0.885,0.427 0.885,0.427 1.188,0.427 false 0.802,1.573 1.052,0.438 false 1.26,0.333 1.573,0.531 0.313,0.198 10 false *a 2.667,1.135 2.844,1.323 0.177,0.188 10 false A

Loosen the bolt and remove the No. 2 intermediate shaft.

Text in Illustration
*a Matchmark

NOTICE:

It is possible to install the intermediate shaft to the same position it was removed from without placing matchmarks due to the dust cover part labeled A. Therefore, do not remove the dust cover from the steering link.


HINT:

If the dust cover is removed/installed or replaced, place matchmarks on the dust cover and steering link.