Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255453 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2611  Telescopic Position Sensor or Telescopic Motor Circuit Malfunction  


DESCRIPTION

The telescopic motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor detects the sliding position in the forward and backward directions of the steering column and outputs a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

C152160E19
0.5,0.135 2.448,0.573 1.948,0.438 10 false Telescopic Steering Contracted Mechanical Lock Position 4.708,0.125 6.646,0.542 1.938,0.417 10 false Telescopic Steering Extended Mechanical Lock Position 1.104,2.042 2.802,2.438 1.698,0.396 10 false Telescopic Steering Contracted Limit Position 4.302,2.021 5.938,2.438 1.635,0.417 10 false Telescopic Steering Extended Limit Position 2.99,1.26 4.135,1.5 1.146,0.24 10 false Operation Range

HINT:

Limit positions can be confirmed on the screen of the intelligent tester.

DTC Code Detection Condition Trouble Area
B2611 The telescopic operation stops within the operation range while operating.
·

Harness or connector

·

Telescopic position sensor or telescopic motor

·

Multiplex tilt and telescopic ECU




WIRING DIAGRAM

C149006E17
0.708,1.042 1.938,1.25 1.229,0.208 10 false Telescopic Motor 4.635,0.938 5.052,1.135 0.417,0.198 10 false TEM+ 4.656,1.719 5.031,1.917 0.375,0.198 10 false TEM- 4.656,2.458 4.979,2.656 0.323,0.198 10 false VCE 4.656,2.854 4.99,3.052 0.333,0.198 10 false TES 4.667,3.25 4.917,3.448 0.25,0.198 10 false E2 0.479,3.385 1.771,3.792 1.292,0.406 10 false Telescopic Position Sensor 4.375,1.427 4.521,1.625 0.146,0.198 10 false 6 4.375,2.177 4.552,2.396 0.177,0.219 10 false 3 4.385,2.573 4.583,2.792 0.198,0.219 10 false 4 4.354,0.813 4.604,1.01 0.25,0.198 10 false A 4.365,1.594 4.635,1.813 0.271,0.219 10 false A 4.354,2.354 4.688,2.552 0.333,0.198 10 false A 4.365,2.75 4.698,2.948 0.333,0.198 10 false A 4.365,3.146 4.698,3.344 0.333,0.198 10 false A 4.292,3.542 4.625,3.74 0.333,0.198 10 false E27 4.365,0.635 4.594,0.802 0.229,0.167 10 false 2 4.333,3.365 4.573,3.563 0.24,0.198 10 false 11 4.385,2.969 4.625,3.167 0.24,0.198 10 false 5 4.646,3.646 5.052,3.844 0.406,0.198 10 false GND 6,0.573 6.313,0.771 0.313,0.198 10 false +B 6,1.406 6.313,1.604 0.313,0.198 10 false +B 6.073,2.146 6.479,2.344 0.406,0.198 10 false 12 V 5.917,3.271 6.49,3.469 0.573,0.198 10 false to CPU 4.646,4.031 6.792,4.26 2.146,0.229 10 false Multiplex Tilt and Telescopic ECU 0.667,4.188 1.865,4.427 1.198,0.24 10 false Telescopic Motor

CAUTION / NOTICE / HINT

HINT:

The wire harness between the multiplex tilt and telescopic ECU and telescopic motor is provided with the steering column assembly.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TELESCOPIC SHORT/LONG)
C106469E06
0.969,0.094 1.448,0.292 0.479,0.198 10 false Extend 2.031,1.854 2.719,2.073 0.688,0.219 10 false Contract

a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering column contracts and extends.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Telesco Operation Telescopic operation Long/Short -


Result
Result Proceed to
The steering column does not contract/extend. A
The steering column contracts/extends. B


A

2.CHECK TELESCOPIC MOTOR

B

3.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)
2.CHECK TELESCOPIC MOTOR
a.
C149086E19
1.083,2.531 0.677,1.458 true 1.073,2.625 0.635,2.99 true 1.458,2.698 1.698,2.938 true 0.125,0.135 2.458,0.573 2.333,0.438 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 1.719,2.948 2.677,3.146 0.958,0.198 10 false Connector A 0.167,1.229 0.781,1.427 0.615,0.198 10 false 2 (TEM+) 0.292,3.031 0.938,3.229 0.646,0.198 10 false 6 (TEM-)

Disconnect connector A from the multiplex tilt and telescopic ECU.


b.

Apply 12 V battery voltage to the multiplex tilt and telescopic ECU connector. Then check the steering wheel telescopic operation.

OK:
Measurement Condition Specified Condition
12 V battery positive (+) lead → Terminal A-2 (TEM+)
12 V battery negative (-) lead → Terminal A-6 (TEM-)
The steering column contracts.
12 V battery positive (+) lead → Terminal A-6 (TEM-)
12 V battery negative (-) lead → Terminal A-2 (TEM+)
The steering column extends.




OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

3.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)
a.
C149088E39
1.24,2.083 1.583,3.042 true 1.083,2.083 0.49,2.521 true 0.885,1.865 0.521,1.604 true 0.115,2.563 0.521,2.771 0.406,0.208 10 false 5 (E2) 1.469,3.083 2.031,3.292 0.563,0.208 10 false 3 (VCE) 0.115,1.406 1.083,1.615 0.969,0.208 10 false Connector A 0.135,0.125 2.625,0.521 2.49,0.396 10 false Component with harness connected: (Multiplex Tilt and Telescopic ECU)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-3 (VCE) - A-5 (E2) Engine switch on (IG) 8 to 16 V




OK

4.CHECK TELESCOPIC POSITION SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (ECU - TELESCOPIC POSITION SENSOR)
4.CHECK TELESCOPIC POSITION SENSOR
a.
C149088E40
1.156,2.094 1.583,3.031 true 1.073,2.094 0.49,2.521 true 0.875,1.875 0.521,1.615 true 0.104,2.563 0.5,2.771 0.396,0.208 10 false 5 (E2) 1.479,3.042 2.042,3.25 0.563,0.208 10 false 4 (TES) 0.125,1.417 1.094,1.625 0.969,0.208 10 false Connector A 0.146,0.125 2.635,0.521 2.49,0.396 10 false Component with harness connected: (Multiplex Tilt and Telescopic ECU)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-4 (TES) - A-5 (E2) Telescopic steering contracting or extending Pulse generation
High: 8 to 16 V
Low: Below 1 V




OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

5.CHECK HARNESS AND CONNECTOR (ECU - TELESCOPIC POSITION SENSOR)
a.
C149086E20
0.979,2.708 0.656,3.01 true 1.354,2.615 1.698,2.958 true 0.094,0.094 2.458,0.552 2.365,0.458 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 0.208,3.021 1.031,3.219 0.823,0.198 10 false Connector A 1.625,2.979 2.198,3.177 0.573,0.198 10 false 3 (VCE)

Disconnect connector A from the multiplex tilt and telescopic ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (VCE) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ECU - BODY GROUND)
a.
U164516E02
1.854,2.615 1.281,3.021 true 0.125,0.167 2.49,0.615 2.365,0.448 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 0.854,3.052 1.5,3.25 0.646,0.198 10 false 11 (GND) 1.969,1.313 2.26,1.51 0.292,0.198 10 false E27

Disconnect the E27 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E27-11 (GND) - Body ground Always Below 1 Ω




OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR