Different voltage values are input to the multiplex tilt and telescopic ECU by operating the tilt and telescopic manual switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should be moved based on the voltage value.
| DTC Code | Detection Condition | Trouble Area |
|---|---|---|
| B2603 | When operating the tilt and telescopic manual switch, an abnormal voltage value is input to the multiplex tilt and telescopic ECU. | ·
Tilt and telescopic manual switch ·
Tilt and telescopic manual switch circuit ·
Multiplex tilt and telescopic ECU |
Use the Data List to check if the tilt and telescopic manual switch is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Tilt Up Switch | Input state of tilt up by manual switch/ON or OFF | ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch |
- |
| Tilt Down Switch | Input state of tilt down by manual switch/ON or OFF | ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch |
- |
| Telesco Short Switch | Input state of telescopic short by manual switch/ON or OFF | ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch |
- |
| Telesco Long Switch | Input state of telescopic long by manual switch/ON or OFF | ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch |
- |
"ON" is displayed on the intelligent tester screen when each switch is turned on.
"OFF" is displayed on the intelligent tester screen when each switch is turned off.
OK
NG
Clear the DTCs (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Disconnect the E27 multiplex tilt and telescopic ECU connector.
Disconnect the E14 headlight dimmer switch or E15 windshield wiper switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E27-4 (VC) - E14-8 (VC) | Always | Below 1 Ω |
| E27-3 (MSW) - E14-10 (MSW) | ||
| E14-8 (VC) - Body ground | Always | 10 kΩ or higher |
| E14-10 (MSW) - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E27-4 (VC) - E15-6 (VC) | Always | Below 1 Ω |
| E27-3 (MSW) - E15-7 (MSW) | ||
| E15-6 (VC) - Body ground | Always | 10 kΩ or higher |
| E15-7 (MSW) - Body ground |
OK
NG
Reconnect the E27 multiplex tilt and telescopic ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E27-4 (VC) - E27-3 (MSW) | Engine switch on (IG) | 4.9 to 5.1 V |
OK
NG
Remove the tilt and telescopic manual switch (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (VC) - 3 (MSW) | Tilt up | 342 to 378 Ω |
| Tilt down | 1890.5 to 2089.5 Ω | |
| Telescopic contract | 750.5 to 829.5 Ω | |
| Telescopic extend | 152 to 168 Ω |
| Result | Proceed to |
|---|---|
| OK (for headlight dimmer switch LH side) | A |
| OK (for headlight dimmer switch RH side) | B |
| NG | C |
A
B
C