Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255453 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2603  Tilt and Telescopic Manual Switch Circuit Malfunction  


DESCRIPTION

Different voltage values are sent to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should operate based on the voltage value.

DTC No. Detection Condition Trouble Area
B2603 When operating the tilt and telescopic switch, an abnormal voltage value is sent to the multiplex tilt and telescopic ECU.
·

Tilt and telescopic switch

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C240527E53
4.938,3.896 7.073,4.146 2.135,0.25 10 false Multiplex Tilt and Telescopic ECU 1.5,3.833 3.385,4.104 1.885,0.271 10 false Tilt and Telescopic Switch 0.729,1.948 1.333,2.188 0.604,0.24 10 false Tilt Down 1.604,1.917 2.344,2.313 0.74,0.396 10 false Telescopic Shorten 2.49,1.948 3.031,2.281 0.542,0.333 10 false Tilt Up 3.354,1.875 4.094,2.25 0.74,0.375 10 false Telescopic Stretch 4.208,2.656 4.385,2.823 0.177,0.167 10 false 3 4.188,1.021 4.323,1.188 0.135,0.167 10 false 1 4.844,2.667 5.042,2.844 0.198,0.177 10 false 18 4.927,1.031 5.073,1.198 0.146,0.167 10 false 5 5.125,1.125 5.427,1.323 0.302,0.198 10 false VC 3.865,1.01 4.115,1.188 0.25,0.177 10 false VC 3.74,2.667 4.125,2.906 0.385,0.24 10 false MSW 5.125,2.771 5.542,2.958 0.417,0.188 10 false MSW 4.938,3.708 5.375,3.896 0.438,0.188 10 false E144 1.5,3.615 1.938,3.813 0.438,0.198 10 false E141

PROCEDURE

1.READ VALUE USING GTS (TILT UP/DOWN SWITCH, TELESCOPIC SHORT/LONG SWITCH)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Check the tilt and telescopic manual switch. Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.

Tilt & Telescopic
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Tilt Up Switch Input state of tilt up switch/
ON or OFF
ON: Tilt up switch activated
OFF: Tilt up switch not activated
-
Tilt Down Switch Input state of tilt down switch/
ON or OFF
ON: Tilt down switch activated
OFF: Tilt down switch not activated
-
Telesco Short Switch Input state of telescopic contract switch/
ON or OFF
ON: Telescopic contract switch activated
OFF: Telescopic contract switch not activated
-
Telesco Long Switch Input state of telescopic extend switch/
ON or OFF
ON: Telescopic extend switch activated
OFF: Telescopic extend switch not activated
-

OK:

"ON" is displayed on the GTS screen when each switch is turned on.

"OFF" is displayed on the GTS screen when each switch is turned off.




OK

2.CONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
a.

Disconnect the E144 multiplex tilt and telescopic ECU connector.


b.

Disconnect the E141 tilt and telescopic switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-5 (VC) - E141-1 (VC) Always Below 1 Ω
E144-18 (MSW) - E141-3 (MSW)
E144-5 (VC) - Body ground 10 kΩ or higher
E144-18 (MSW) - Body ground




OK

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)
a.
U165141E02
1.177,0.969 1.156,0.688 false 1.167,1.458 1.167,1.177 false 0.177,0.135 0.375,0.313 0.198,0.177 10 false *a 1.563,0.385 1.958,0.563 0.396,0.177 10 false E144 1.042,0.49 1.302,0.667 0.26,0.177 10 false VC 1.01,1.5 1.438,1.677 0.427,0.177 10 false MSW

Reconnect the multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E144-5 (VC) - E144-18 (MSW) Engine switch on (IG) 4.9 to 5.1 V


Text in Illustration
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)



OK

5.CHECK TILT AND TELESCOPIC SWITCH

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

5.CHECK TILT AND TELESCOPIC SWITCH
a.
C240949E03
0.123,0.059 0.380,0.213 0.257,0.154 10 *a 2.386,1.684 2.621,1.863 0.235,0.179 10 VC 1.961,1.415 2.495,1.552 2.495,1.552 2.495,1.633 false 0.479,1.701 0.908,1.862 0.429,0.161 10 MSW 1.485,1.423 0.673,1.57 0.673,1.57 0.673,1.684 false

Remove the tilt and telescopic switch (See page Steering>STEERING COLUMN>TILT AND TELESCOPIC MANUAL SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (VC) - 3 (MSW) Tilt up 342 to 378 Ω
Tilt down 1890.5 to 2089.5 Ω
Telescopic contract 750.5 to 829.5 Ω
Telescopic extend 152 to 168 Ω


Text in Illustration
*a Component without harness connected
(Tilt and Telescopic Switch)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE TILT AND TELESCOPIC SWITCH