Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255476 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Display Signal Circuit between Multi-display Controller and Television Display  


DESCRIPTION

This is the display signal circuit between the multi-media module receiver assembly and the television display assembly.

WIRING DIAGRAM

E333076E02
0.501,2.274 2.776,2.549 2.275,0.275 10 Television Display Assembly RH 5.5,1.233 5.989,1.370 0.489,0.137 10 GVO1+ 0.501,2.1 1.482,2.270 0.981,0.170 10 c45 1.809,1.104 2.299,1.241 0.489,0.137 10 2 5.275,1.104 5.419,1.241 0.144,0.137 10 2 5.5,0.808 5.989,0.945 0.489,0.137 10 GVO1- 1.809,0.682 2.299,0.820 0.489,0.137 10 1 2.476,1.762 2.965,1.899 0.489,0.137 10 * 4.636,1.762 5.125,1.899 0.489,0.137 10 * 2.476,4.307 2.965,4.444 0.489,0.137 10 * 4.636,4.307 5.125,4.444 0.489,0.137 10 * 5.275,0.682 5.419,0.820 0.144,0.137 10 1 5.5,1.658 5.989,1.796 0.489,0.137 10 GVG1 1.809,1.541 2.299,1.678 0.489,0.137 10 3 5.275,1.541 5.419,1.678 0.144,0.137 10 3 0.501,4.837 2.754,5.112 2.253,0.275 10 Television Display Assembly LH 0.921,5.369 1.914,5.564 0.993,0.195 10 : GVIF Cable 2.442,5.369 3.435,5.564 0.993,0.195 10 *: Shielded 5.5,3.78 5.989,3.917 0.489,0.137 10 GVO2+ 5.36,4.719 6.170,4.889 0.810,0.170 10 L82 5.36,4.877 6.847,5.352 1.487,0.475 10 Multi-display Controller Sub-assembly 0.501,4.663 1.482,4.832 0.981,0.170 10 c52 1.29,3.78 1.724,3.917 0.434,0.137 10 GVI2+ 1.809,3.658 2.299,3.796 0.489,0.137 10 2 5.275,3.658 5.419,3.796 0.144,0.137 10 5 5.5,3.354 5.989,3.492 0.489,0.137 10 GVO2- 1.275,3.354 1.699,3.492 0.424,0.137 10 GVI2- 1.809,3.229 2.299,3.366 0.489,0.137 10 1 5.275,3.229 5.419,3.366 0.144,0.137 10 4 5.5,4.205 5.989,4.342 0.489,0.137 10 GVG2 1.29,4.205 1.698,4.342 0.408,0.137 10 GVG2 1.809,4.088 2.299,4.225 0.489,0.137 10 3 5.275,4.088 5.419,4.225 0.144,0.137 10 6 1.286,1.223 1.720,1.361 0.434,0.137 10 GVI1+ 1.271,0.798 1.694,0.935 0.424,0.137 10 GVI1- 1.286,1.649 1.694,1.786 0.408,0.137 10 GVG1

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
a.

Check if the GVIF cable connectors between the multi-display controller sub-assembly and the television display assembly have any connection problems (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

There are no connection problems.




OK

2.CHECK HARNESS AND CONNECTOR (GVIF CABLE)

NG

REMOVE CONNECTION PROBLEMS (GVIF CABLE)

2.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
a.
U166484E02
1.958,0.865 2.167,0.24 2.167,0.24 2.323,0.24 false 2.26,0.854 2.604,0.521 2.604,0.521 2.76,0.521 false 2.208,1.167 2.542,1.427 2.542,1.427 2.781,1.427 false 1.885,2.75 2.208,2.563 2.208,2.563 2.458,2.563 false 1.521,2.531 1.177,1.802 1.177,1.802 1.073,1.802 false 1.917,2.521 2.115,1.76 2.115,1.76 2.354,1.76 false 1.448,0.854 1.24,0.229 1.24,0.229 1.083,0.229 false 1.198,0.865 0.844,0.531 0.844,0.531 0.688,0.531 false 1.219,1.188 0.927,1.479 0.927,1.479 0.677,1.479 false 0.052,0 0.26,0.198 0.208,0.198 10 false *a 0.052,1.75 0.26,1.948 0.208,0.198 10 false *b 2.385,0.146 2.885,0.323 0.5,0.177 10 false GVO2- 2.813,0.458 3.313,0.635 0.5,0.177 10 false GVO2+ 2.854,1.344 3.292,1.521 0.438,0.177 10 false GVG2 0.26,0.885 0.542,1.063 0.281,0.177 10 false L82 0.448,1.771 1,1.948 0.552,0.177 10 false GVI1-*A 2.417,1.688 3.021,1.865 0.604,0.177 10 false GVI1+*A 2.573,2.479 3.198,2.656 0.625,0.177 10 false GVG1*A 0.26,2.458 0.531,2.635 0.271,0.177 10 false c45 0.26,2.844 0.552,3.021 0.292,0.177 10 false c52 0.74,2.438 0.979,2.615 0.24,0.177 10 false *A 0.74,2.854 0.979,3.031 0.24,0.177 10 false *B 0.26,0.479 0.76,0.656 0.5,0.177 10 false GVO1- 0.563,0.125 1.063,0.302 0.5,0.177 10 false GVO1+ 0.24,1.396 0.677,1.573 0.438,0.177 10 false GVG1 0.458,2.01 1.01,2.188 0.552,0.177 10 false GVI2-*B 2.417,1.917 3.021,2.094 0.604,0.177 10 false GVI2+*B 2.573,2.75 3.198,2.927 0.625,0.177 10 false GVG2*B

Remove the GVIF cable from the multi-display controller sub-assembly and television display assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
L82-1 (GVO1-) - c45-1 (GVI1-) Always Below 1 Ω
L82-2 (GVO1+) - c45-2 (GVI1+) Always Below 1 Ω
L82-3 (GVG1) - c45-3 (GVG1) Always Below 1 Ω
L82-1 (GVO1-) or c45-1 (GVI1-) - Body ground Always 10 kΩ or higher
L82-2 (GVO1+) or c45-2 (GVI1+) - Body ground Always 10 kΩ or higher
L82-3 (GVG1) or c45-3 (GVG1) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
L82-4 (GVO2-) - c52-1 (GVI1-) Always Below 1 Ω
L82-5 (GVO2+) - c52-2 (GVI1+) Always Below 1 Ω
L82-6 (GVG2) - c52-3 (GVG1) Always Below 1 Ω
L82-4 (GVO2-) or c52-1 (GVI1-) - Body ground Always 10 kΩ or higher
L82-5 (GVO2+) or c52-2 (GVI1+) - Body ground Always 10 kΩ or higher
L82-6 (GVG2) or c52-3 (GVG1) - Body ground Always 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*a GVIF Cable
(to Multi-display Controller Sub-assembly)
*b GVIF Cable
(to Television Display Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE HARNESS AND CONNECTOR (GVIF CABLE)