Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/ Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255478 AUDIO AND VISUAL SYSTEM(w/ Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Navigation System)  AVC-LAN Circuit  


DESCRIPTION

Each audio system component connected to the AVC-LAN (communication bus) transfers switch signals using the audio visual communication local area network.

If a short to +B or short to ground occurs in the AVC-LAN, the audio system will not function normally because communication is not possible.

WIRING DIAGRAM

C260263E01
5.309,0.636 5.986,0.820 0.677,0.184 10 TX3+ 5.153,1.736 6.496,2.119 1.343,0.383 10 Multi-media Module Receiver Assembly 5.072,0.549 5.362,0.747 0.290,0.198 10 45 5.305,1.085 5.981,1.268 0.677,0.184 10 TX3- 5.067,1.039 5.357,1.238 0.290,0.198 10 46 2.046,0.54 2.336,0.738 0.290,0.198 10 7 2.041,1.03 2.331,1.228 0.290,0.198 10 19 5.153,1.571 5.510,1.734 0.357,0.163 10 F77 1.674,0.636 2.010,0.820 0.336,0.184 10 TX+ 1.011,1.638 3.284,1.822 2.273,0.184 10 Multi-display Assembly 0.917,2.367 3.167,2.551 2.250,0.184 10 : AVC-LAN Communication Line 1.671,1.085 2.008,1.268 0.336,0.184 10 TX- 1.011,1.473 1.368,1.635 0.357,0.163 10 F79

PROCEDURE

1.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
E238990E12
1.817,1.75 2.216,1.926 0.399,0.177 10 TX3- 2.433,1.726 2.832,1.903 0.399,0.177 10 TX3+ 2.279,1.333 2.011,1.742 false 2.386,1.335 2.66,1.701 false

Remove the multi-media module receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
45 (TX3+) - 46 (TX3-) Always 60 to 80 Ω




OK

2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
HINT:

For details of the connectors, refer to Terminals of ECU (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>TERMINALS OF ECU).


a.

Referring to the following AVC-LAN wiring diagram, check all AVC-LAN circuits.

i.

Disconnect all connectors in all AVC-LAN circuits.


ii.

Check for an open or short in all AVC-LAN circuits.

OK:

There is no open or short circuit.





OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

When disconnecting a slave unit causes the master unit to return to normal operation, this indicates that the slave unit is malfunctioning. Replace the malfunctioning slave unit.



OK:

Master unit returns to normal operation.




OK

REPLACE MALFUNCTIONING PARTS

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE