Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/ Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255478 AUDIO AND VISUAL SYSTEM(w/ Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Navigation System)  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The circuit is necessary for the Automatic Sound Levelizer (ASL) built into the stereo component amplifier assembly.

Speed signals are received from the combination meter assembly and used for the ASL.

The ASL function automatically adjusts the sound volume in order to clear audio quality even when vehicle noise increases (as vehicle noise increases, the volume is turned up etc.).

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E195676E08
5.791,3.722 7.074,4.072 1.283,0.350 10 Stereo Component Amplifier Assembly 0.617,2.511 2.041,2.695 1.424,0.184 10 from Skid Control ECU 1.069,0.603 2.209,1.118 1.140,0.515 10 to Multi-media Module Receiver Assembly 2.718,3.293 3.938,3.701 1.221,0.408 10 Combination Meter Assembly 3.729,2.513 3.938,2.683 0.209,0.170 10 +S 4.002,2.413 4.114,2.566 0.112,0.154 10 4 5.898,0.5 6.107,0.670 0.209,0.170 10 17 6.151,0.604 6.500,0.757 0.348,0.154 10 SPD 5.792,3.556 6.088,3.725 0.296,0.170 10 F74 2.718,3.125 2.984,3.279 0.266,0.154 10 E7

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - COMBINATION METER)
a.

Disconnect the F74 stereo component amplifier assembly connector and E7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-17 (SPD) - F7-4 (+S) Always Below 1 Ω
F74-17 (SPD) - Body ground Always 10 kΩ or higher




OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.

Reconnect the E7 combination meter assembly connector.


b.
U166281E01
0.085,0.031 0.255,0.220 0.170,0.188 10 *a 1.489,0.346 1.770,0.516 0.281,0.170 10 F74 1.019,1.779 1.444,1.958 0.424,0.179 10 SPD 0.941,1.252 1.226,1.738 false

Check the input waveform.

i.

Connect an oscilloscope to terminal F74-17 (SPD) and body ground.


ii.

Turn the engine switch on (IG).


iii.

Turn a wheel slowly.

Text in Illustration
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


iv.
E349035E03
0.927,1.635 1.167,1.865 0.24,0.229 10 false (A) 2.854,1.271 3.24,1.5 0.385,0.229 10 false GND

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F74-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Driving at approx. 20 km/h (12 mph)

OK:

The waveform is displayed as shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

REPLACE PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG