Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  AVC-LAN Circuit  


DESCRIPTION

Each audio system component connected to the AVC-LAN (communication bus) transfers the switch signals by the audio visual communication local area network.

If a short to +B or short to ground occurs in this AVC-LAN, the audio system will not function normally as communication is stopped.

PROCEDURE

1.INSPECT RADIO RECEIVER ASSEMBLY
a.
U166127E01
0.12,0.1 0.276,0.287 0.156,0.186 10 *1 0.12,2.655 0.297,2.811 0.178,0.156 10 *2 1.56,0.497 1.790,0.671 0.230,0.174 10 F1 0.338,3.789 0.604,3.941 0.266,0.152 10 F55 0.51,0.613 0.902,0.752 0.392,0.139 10 ATX+ 2.263,2.391 2.663,2.569 0.400,0.178 10 ATX- 0.974,0.674 1.749,1.567 false 1.746,1.987 2.198,2.446 false 0.325,3.036 0.705,3.201 0.380,0.165 10 TXM- 2.648,4.125 3.071,4.287 0.423,0.162 10 TXM+ 0.775,3.111 1.551,3.888 false 1.81,3.967 2.582,4.201 false

Disconnect the F1 and F55 radio receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-5 (ATX+) - F1-15 (ATX-) Always 60 to 80 Ω
F55-9 (TXM+) - F55-10 (TXM-) Always 60 to 80 Ω


Text in Illustration
*1 Component without harness connected
(Radio Receiver Assembly)
*2 Component without harness connected
(Radio Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
HINT:

For details of the connectors, refer to Terminals of ECU (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/o Navigation System)>TERMINALS OF ECU).


a.

Referring to the following AVC-LAN wiring diagram, check all AVC-LAN circuits.

i.

Disconnect all connectors in all AVC-LAN circuits.


ii.

Check for an open or short in all AVC-LAN circuits.

OK:

There is no open or short circuit.


E194159E11
5.229,3.938 6.552,4.365 1.323,0.427 10 false Multi-media Interface ECU*2 0.948,4.115 1.958,4.51 1.01,0.396 10 false Radio Receiver Assembly*1 2.427,1.25 2.823,1.469 0.396,0.219 10 false F1 2.427,1.74 2.823,1.958 0.396,0.219 10 false F1 1.927,1.167 2.323,1.385 0.396,0.219 10 false ATX+ 1.927,1.635 2.323,1.854 0.396,0.219 10 false ATX- 2.458,1.021 2.708,1.208 0.25,0.188 10 false 5 2.427,1.521 2.719,1.708 0.292,0.188 10 false 15 5.25,1.25 5.646,1.469 0.396,0.219 10 false TX+ 5.25,1.708 5.646,1.927 0.396,0.219 10 false TX- 4.917,1.24 5.177,1.417 0.26,0.177 10 false F18 4.917,1.729 5.188,1.896 0.271,0.167 10 false F18 4.917,3.021 5.188,3.198 0.271,0.177 10 false L40 4.917,3.51 5.188,3.667 0.271,0.156 10 false L40 5.25,3.021 5.646,3.24 0.396,0.219 10 false TX1- 5.26,3.479 5.656,3.698 0.396,0.219 10 false TX1+ 2.396,3.031 2.656,3.219 0.26,0.188 10 false F55 2.396,3.51 2.656,3.677 0.26,0.167 10 false F55 4.948,2.802 5.146,3.021 0.198,0.219 10 false 10 4.99,3.25 5.188,3.469 0.198,0.219 10 false 9 4.99,1.031 5.229,1.229 0.24,0.198 10 false 8 4.99,1.521 5.208,1.698 0.219,0.177 10 false 7 2.469,3.323 2.677,3.5 0.208,0.177 10 false 9 2.406,2.813 2.646,2.99 0.24,0.177 10 false 10 1.906,3.5 2.313,3.698 0.406,0.198 10 false TXM+ 1.906,3.021 2.271,3.24 0.365,0.219 10 false TXM- 0.292,4.906 1.563,5.146 1.271,0.24 10 false *1: Master Unit 0.292,5.229 1.563,5.469 1.271,0.24 10 false *2: Slave Unit 0.167,0.031 2.323,0.229 2.156,0.198 10 false AVC-LAN WIRING DIAGRAM: 5.208,2.156 6.625,2.49 1.417,0.333 10 false Stereo Component Amplifier Assembly*2




OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

When disconnecting a slave unit causes the master unit to return to normal operation, this indicates that the slave unit is malfunctioning. Replace the malfunctioning slave unit.



OK:

Master unit returns to normal operation.




OK

REPLACE MALFUNCTIONING PARTS

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE