Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Dimmer Signal Circuit  


DESCRIPTION

The radio receiver assembly uses this circuit to communicate with the main body ECU (cowl side junction block LH) via a direct line. The main body ECU (cowl side junction block LH) uses this circuit to send an auto dimmer signal to the radio receiver assembly. The main body ECU (cowl side junction block LH) detects the position of the light control switch according to the resistance. When the light control switch is set to the head/tail position, the resistance between the head/tail terminal and body ground is below 1 Ω. When the light control switch is set to the head/tail position, the main body ECU (cowl side junction block LH) sends an auto dimmer signal to the radio receiver assembly. When the radio receiver assembly receives an auto dimmer signal from the main body ECU (cowl side junction block LH), the radio receiver assembly causes instrument panel illumination to be dimmed.

WIRING DIAGRAM

E182033E10
0.438,2.385 3.427,2.615 2.99,0.229 10 false Main Body ECU (Cowl Side Junction Block LH) 5.26,2.25 6.885,2.438 1.625,0.188 10 false Radio Receiver Assembly 1.01,0.729 1.458,0.917 0.448,0.188 10 false ACAN 5.719,0.75 6.177,0.948 0.458,0.198 10 false ADIM 5.354,0.76 5.656,0.927 0.302,0.167 10 false F19 5.396,0.521 5.583,0.688 0.188,0.167 10 false 20 1.531,0.667 1.74,0.813 0.208,0.146 10 false 16 0.438,2.219 0.74,2.385 0.302,0.167 10 false E2 5.396,1.542 5.698,1.708 0.302,0.167 10 false F1 5.406,1.292 5.594,1.458 0.188,0.167 10 false 20 5.719,1.51 6.177,1.708 0.458,0.198 10 false GND

PROCEDURE

1.INSPECT MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
a.
U166097E01
0.421,1.016 0.716,1.200 0.295,0.184 10 F19 2.45,2.838 3.189,3.022 0.739,0.184 10 ADIM 2.501,2.483 2.587,2.838 false 0.318,0.139 0.613,0.323 0.295,0.184 10 *1

Disconnect the F19 radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F19-20 (ADIM) - Body ground Engine switch on (IG), automatic light control sensor covered by hand, and light control switch tail or head position 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to Radio Receiver Assembly)



OK

2.INSPECT RADIO RECEIVER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAIN BODY ECU)
2.INSPECT RADIO RECEIVER ASSEMBLY
a.

Disconnect the F1 radio receiver assembly connector.


b.
U165828E02
2.406,1.781 2.625,1.875 false 0.323,1.438 0.75,1.677 0.427,0.24 10 false F1 2.688,1.833 3.052,2.073 0.365,0.24 10 false GND 0.24,0.115 0.667,0.354 0.427,0.24 10 false *1

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
F1-20 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*1 Front view of wire harness connector
(to Radio Receiver Assembly)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the F19 radio receiver assembly and E2 main body ECU (cowl side junction block LH) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E2-16 (ACAN) - F19-20 (ADIM) Always Below 1 Ω
F19-20 (ADIM) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR