Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

This circuit sends the microphone signal from the map light assembly (telephone microphone assembly) to the radio receiver assembly.

It also supplies power source from the radio receiver assembly to the map light assembly (telephone microphone assembly).

WIRING DIAGRAM

E177629E09
0.334,3.925 1.837,4.118 1.503,0.193 10 Map Light Assembly 5.896,3.925 6.962,4.289 1.066,0.364 10 Radio Receiver Assembly 0.334,3.77 0.667,3.933 0.333,0.163 10 R7 5.896,3.77 6.229,3.933 0.333,0.163 10 F54 0.685,0.632 1.161,0.927 0.475,0.295 10 SNS2 0.786,1.291 1.161,1.458 0.376,0.167 10 MI1+ 0.797,1.921 1.162,2.096 0.365,0.175 10 MIC- 0.79,2.575 1.161,2.750 0.371,0.175 10 ACC 6.043,0.618 6.518,0.913 0.475,0.295 10 SNS2 6.043,1.249 6.518,1.543 0.475,0.295 10 MIN+ 6.043,1.945 6.518,2.240 0.475,0.295 10 MIN- 6.043,2.538 6.491,2.763 0.448,0.225 10 MACC 6.043,3.182 6.491,3.407 0.448,0.225 10 SGND 3.913,3.322 4.604,3.617 0.691,0.295 10 (Shielded) 2.695,3.322 3.385,3.617 0.691,0.295 10 (Shielded) 5.782,0.497 5.980,0.657 0.198,0.161 10 1 1.315,1.172 1.549,1.332 0.235,0.161 10 27 1.319,0.532 1.554,0.692 0.235,0.161 10 20 1.319,1.835 1.554,1.995 0.235,0.161 10 26 1.329,2.451 1.563,2.612 0.235,0.161 10 25 5.782,1.844 6.017,2.005 0.235,0.161 10 5 5.782,1.2 6.017,1.360 0.235,0.161 10 2 5.782,2.456 6.017,2.616 0.235,0.161 10 3 5.782,3.065 6.017,3.225 0.235,0.161 10 6 0.324,4.256 2.531,4.449 2.207,0.193 10 (Telephone Microphone Assembly)

PROCEDURE

1.INSPECT RADIO RECEIVER ASSEMBLY
a.
U166081E01
0.258,0.175 0.505,0.367 0.247,0.192 10 *1 2.648,1.181 2.951,1.343 0.303,0.163 10 F54 0.292,2.22 0.740,2.397 0.448,0.177 10 MACC 1.602,1.573 0.556,2.2 false 2.182,2.32 2.629,2.497 0.448,0.177 10 SGND 2.399,1.719 2.847,1.895 0.448,0.177 10 MIN- 1.867,1.796 2.214,2.32 false 2.355,1.807 2.066,1.781 false

Disconnect the F54 radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F54-3 (MACC) - Body ground Engine switch on (IG) 4 to 6 V


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-6 (SGND) - Body ground Always Below 1 Ω
F54-5 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*1 Component without harness connected
(Radio Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - RADIO RECEIVER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - RADIO RECEIVER ASSEMBLY)
a.

Disconnect the R7 map light assembly and F54 radio receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R7-20 (SNS2) - F54-1 (SNS2) Always Below 1 Ω
R7-27 (MI1+) - F54-2 (MIN+) Always Below 1 Ω
R7-26 (MIC-) - F54-5 (MIN-) Always Below 1 Ω
R7-25 (ACC) - F54-3 (MACC) Always Below 1 Ω
R7-20 (SNS2) - Body ground Always 10 kΩ or higher
R7-27 (MI1+) - Body ground Always 10 kΩ or higher
R7-26 (MIC-) - Body ground Always 10 kΩ or higher
R7-25 (ACC) - Body ground Always 10 kΩ or higher
F54-6 (SGND) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.
U166108E01
1.615,0.189 1.810,0.370 0.195,0.181 10 R7 0.12,0.054 0.290,0.228 0.170,0.174 10 *1 1.339,1.634 1.852,1.808 0.512,0.174 10 MIC- 2.047,1.634 2.448,1.808 0.401,0.174 10 SNS2 2.267,1.22 2.267,1.634 false 1.536,1.22 1.536,1.634 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R7-20 (SNS2) - R7-26 (MIC-) Always Below 1 Ω


Text in Illustration
*1 Component without harness connected
(Map Light Assembly)



OK

4.INSPECT MAP LIGHT ASSEMBLY

NG

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.INSPECT MAP LIGHT ASSEMBLY
a.
U166109E01
1.622,0.471 1.912,0.634 0.290,0.163 10 R7 0.151,0.131 0.303,0.287 0.152,0.156 10 *1 2.894,1.071 3.299,1.226 0.405,0.156 10 MIC- 0.313,0.891 0.741,1.047 0.428,0.156 10 MI1+ 2.846,1.155 1.539,1.985 false 0.753,0.991 1.435,1.98 false

Reconnect the radio receiver assembly connector.


b.

Reconnect the map light assembly connector.


c.

Turn the engine switch on (ACC).


d.

Connect an oscilloscope to terminals R7-27 (MI1+) and R7-26 (MIC-) of the map light assembly connector.


e.

Check the waveform of the telephone microphone assembly using an oscilloscope.

Result
Result Proceed to
A waveform synchronized with the voice input to the telephone microphone assembly is output A
A waveform synchronized with the voice input to the telephone microphone assembly is not output B


Text in Illustration
*1 Component with harness connected
(Map Light Assembly)


A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL).


b.

Check if the same malfunction recurs.

Result
Result Proceed to
Malfunction does not recur
(returns to normal)
A
Malfunction recurs B



A

END

B