Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255486 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E335242E02
5.896,2.073 6.917,2.521 1.021,0.448 10 false Radio Receiver Assembly 2.729,2 4.021,2.354 1.292,0.354 10 false No. 2 Antenna Cord Sub-assembly 1.229,2.021 2.448,2.375 1.219,0.354 10 false No. 1 Amplifier Antenna Assembly 0.698,0.115 2.594,0.479 1.896,0.365 10 false Quarter Window Assembly (Window Glass Antenna Wire) 5.51,0.802 5.615,0.99 0.104,0.188 10 false 3 4.333,0.833 4.438,1.021 0.104,0.188 10 false 4 3.927,0.813 4.031,1 0.104,0.188 10 false 4 2.74,0.844 2.844,1.031 0.104,0.188 10 false 4 5.51,1.146 5.615,1.302 0.104,0.156 10 false 5 4.333,1.177 4.438,1.333 0.104,0.156 10 false 2 3.927,1.167 4.031,1.323 0.104,0.156 10 false 2 2.74,1.188 2.844,1.344 0.104,0.156 10 false 2 5.99,0.917 6.542,1.073 0.552,0.156 10 false MAIN 5.99,1.219 6.49,1.375 0.5,0.156 10 false ANT+ 5.896,1.896 6.177,2.052 0.281,0.156 10 false RA 4.5,1.979 5.448,2.333 0.948,0.354 10 false Antenna Cord Sub-assembly

PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.




OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.




OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK RADIO RECEIVER ASSEMBLY
3.CHECK RADIO RECEIVER ASSEMBLY
a.
E276819

Remove the antenna connector from the radio receiver assembly.


b.

Turn the ignition switch ACC with the radio receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




OK

4.INSPECT QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)

NG

4.INSPECT QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)
a.

Inspect the quarter window assembly (window glass antenna wire) (See page Audio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR).



OK

5.INSPECT RADIO RECEIVER ASSEMBLY

NG

5.INSPECT RADIO RECEIVER ASSEMBLY
a.

Disconnect the RA radio receiver assembly connector.


b.
E277921E01
1.063,0.781 1.281,0.781 1.281,0.781 1.531,1.042 true 2.333,0.635 2.083,0.635 2.083,0.635 1.833,0.885 true 2.354,1.583 2.104,1.583 2.104,1.583 1.833,1.271 true 0.677,0.698 1.208,0.885 0.531,0.188 10 false ANT+ 2.375,0.552 2.906,0.74 0.531,0.188 10 false 2 2.396,1.5 2.927,1.688 0.531,0.188 10 false 4

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC, radio switch on 11 to 14 V




OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
U166479E01
0.087,0 0.310,0.181 0.223,0.181 10 *a 0.726,0.893 1.095,1.074 0.369,0.181 10 RA 0.087,1.752 0.310,1.934 0.223,0.181 10 *b 0.573,1.407 0.947,1.589 0.373,0.181 10 MAIN 2.484,0.582 2.931,0.763 0.446,0.181 10 ANT+ 1.043,1.479 1.252,1.479 1.252,1.479 1.563,1.205 false 2.457,0.661 2.248,0.661 2.248,0.661 1.963,0.944 false

Disconnect the antenna connector from the radio receiver assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 4 Always Below 1 Ω
RA-5 (ANT+) - 2 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Radio Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)



OK

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E329647E02
0.138,0 0.504,0.356 0.367,0.356 10 *a 0.138,1.55 0.504,1.906 0.367,0.356 10 *b

Disconnect the antenna connector from the antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4 Always Below 1 Ω
2 - 2 Always Below 1 Ω
4 - Body ground Always 10 kΩ or higher
2 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)



OK

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly with a known good one and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL).

OK:

Radio broadcasts can be received.




OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG