Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E305443E07
5.729,1.906 6,2.115 0.271,0.208 10 false RA 5.729,2.052 7.031,2.427 1.302,0.375 10 false Multi-media Module Receiver Assembly 5.969,0.833 6.427,1 0.458,0.167 10 false MAIN 5.969,1.125 6.438,1.344 0.469,0.219 10 false SUB 5.969,1.552 6.406,1.75 0.438,0.198 10 false ANT+ 4.521,1.99 5.469,2.323 0.948,0.333 10 false Antenna Cord Sub-assembly 2.802,1.99 4.125,2.49 1.323,0.5 10 false No. 2 Antenna Cord Sub-assembly 1.01,1.979 2.521,2.479 1.51,0.5 10 false No. 1 Amplifier Antenna Assembly 0.719,0.146 2.615,0.646 1.896,0.5 10 false Quarter Window Glass (Window Glass Antenna Wire) 2.74,0.771 3.104,0.99 0.365,0.219 10 false 4 2.74,1.031 3.073,1.25 0.333,0.219 10 false 3 2.74,1.323 3.094,1.563 0.354,0.24 10 false 2 5.5,0.75 5.969,0.938 0.469,0.188 10 false 3 5.5,1.052 5.927,1.188 0.427,0.135 10 false 1 5.5,1.313 5.927,1.563 0.427,0.25 10 false 5 4.344,0.771 4.844,1.021 0.5,0.25 10 false 4 4.344,1.021 4.792,1.26 0.448,0.24 10 false 3 4.354,1.313 4.813,1.552 0.458,0.24 10 false 2 3.906,0.781 4.146,1.021 0.24,0.24 10 false 4 3.906,1.052 4.115,1.25 0.208,0.198 10 false 3 3.906,1.344 4.115,1.563 0.208,0.219 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Check that the antenna cable is properly installed and does not have any sharp bends, pinching or loose connections.


PROCEDURE

1.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station





OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

NOTICE:

Do not remove optional components without permission of the customer.


OK:

Optional components are installed.




OK

3.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
E276819

Remove the antenna connector from the multi-media module receiver assembly.


b.

Turn the engine switch on (ACC) with the multi-media module receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the multi-media module receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speaker.




OK

4.CHECK QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

4.CHECK QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)
a.

Inspect the quarter window glass (window glass antenna wire) (See page Audio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR).



OK

5.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

5.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
U156638E01
0.095,0.051 0.271,0.228 0.177,0.177 10 *a 0.772,0.971 1.066,1.121 0.295,0.150 10 RA 0.705,1.404 1.108,1.575 0.402,0.171 10 ANT+ 1.552,1.083 1.136,1.404 false

Disconnect the multi-media module receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
RA-5 (ANT+) - Body ground Engine switch on (ACC), radio switch on and FM or AM selected 11 to 14 V


Text in Illustration
*a Component without harness connected
(Multi-media Module Receiver Assembly)



OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
U156744E01
0.087,0 0.310,0.181 0.223,0.181 10 *a 0.726,0.893 1.095,1.074 0.369,0.181 10 RA 0.624,0.345 0.956,0.526 0.332,0.181 10 SUB 0.087,1.752 0.310,1.934 0.223,0.181 10 *b 1.043,0.416 1.252,0.416 1.252,0.416 1.563,0.727 false 0.573,1.407 0.947,1.589 0.373,0.181 10 MAIN 2.484,0.582 2.931,0.763 0.446,0.181 10 ANT+ 1.043,1.479 1.252,1.479 1.252,1.479 1.563,1.205 false 2.457,0.661 2.248,0.661 2.248,0.661 1.963,0.944 false

Remove the antenna connector from the multi-media module receiver assembly.


b.

Remove the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 4 Always Below 1 Ω
RA-1 (SUB) - 3 Always Below 1 Ω
RA-5 (ANT+) - 2 Always Below 1 Ω
RA-3 (MAIN) or 4 - Body ground Always 10 kΩ or higher
RA-1 (SUB) or 3 - Body ground Always 10 kΩ or higher
RA-5 (ANT+) or 2 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)



OK

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E329647E01
0.138,0 0.504,0.356 0.367,0.356 10 *a 0.138,1.55 0.504,1.906 0.367,0.356 10 *b

Remove the antenna connector from the antenna cord sub-assembly.


b.

Remove the antenna connector from the No. 1 amplifier antenna assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4 Always Below 1 Ω
3 - 3 Always Below 1 Ω
2 - 2 Always Below 1 Ω
4 or 4 - Body ground Always 10 kΩ or higher
3 or 3 - Body ground Always 10 kΩ or higher
2 or 2 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)



OK

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly new or known good one and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL).

OK:

Radio broadcasts can be received.




OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY